Korg TRITON Extreme Manual Download

Page: 42 / 354

Program

In “From” select the source mode, bank, and number of
the effect to be copied.

You can select a bank by pressing the BANK [A]–[N]
keys.

Select which of the effects you wish to copy.
You can also copy from a master effect. If “All” is
checked

, all effect settings will be copied (i.e., the con-

tents of the Insert FX page and the effect parameters of
IFX 1–5, but not “Ctrl Ch”).

If you are copying from a master effect, the result may
not be identical, due to differences in the routing and
level settings of a master effect.

Select the insert effect copy destination.
If you check “Post IFX Mixer Setting,” the “Chain,”
“Pan (CC#8),” “BUS Sel.,” “Send 1” and “Send 2” set-
tings that follow the copy source insert effect will also be
copied. If this is unchecked, only the effect type and its
parameters will be copied.

To execute the Copy Insert Effect command, press the
OK button

. To cancel, press the Cancel button.

8–1B: Swap Insert Effect

This command swaps (exchanges) insert effect settings.

Select “Swap Insert Effect” to access the dialog box.

In “Source 1” and “Source 2,” select each of the insert
effects that you wish to swap.

To execute the Swap Insert Effect command, press the
OK button

. To cancel, press the Cancel button.

8–2: Insert FX

Here you can select the type of each insert effect, turn it on/
off, and make chain settings.
The direct sound (Dry) of an insert effect is always stereo
input and output. The input/output of the effect sound
(Wet) will depend on the effect type (

☞

p.206).

8–2a: IFX1, 2, 3, 4, 5

IFX1, 5

[000...089]

IFX2, 3, 4

[000...102]

Selects the type of each insert effect.
For “IFX1” and “IFX5” you can select from 90 types of effect:
000: No Effect – 089: Reverb-Gate

. Double-size effects can-

not be used.
For “IFX2,” “IFX3” and “IFX4” you can select from 103
types of effect: 000: No Effect – 102: Hold Delay.
If you select a double-size effect, the insert effect that follows
will be unavailable. For example if you select a double-size
effect for “IFX2,” “IFX3” cannot be used. Up to two double-
size effects can be used. (You can use a normal size effect for
“IFX1,” and double-size effects for “IFX2” and “IFX4.”)
(

☞

p.206)

Category/IFX Select menu:

When you press the popup button, a “Category/IFX Select”
list will appear. Press a tab to select a category of effects, and
select an effect from that category. Press the OK button to
execute, or press the Cancel button to cancel.

IFX1, 2, 3, 4, 5 On/Off

[Off, ON]

Switches the insert effect on/off.
When this is OFF, the input will be output unchanged. (For
000: No Effect

, on/off will produce the same result.)

Each time you press this, the setting will alternate between
on/off.

Control change #CC92 can be used to turn off all of the
insert effects at once. A value of 0 will be off, and a
value of 1–127 will be the original setting. This message
is received on the global MIDI channel specified by
“MIDI Channel” (Global P1: 1–1a).

Chain

[Off, On]

Switch “chain” on/off for each insert effect.

For example if the “Chain” check box between IFX1 and
IFX2 is checked, IFX1 and IFX2 will be connected in series. If
“BUS Select” (8–1c) is set to IFX1, IFX1 and IFX2 will be
inserted in series.
A maximum of five insert effects (IFX1–IFX5) can be
inserted in series. When effects are chained, the “PAN
(CC#8)

,” “BUS Select,” “Send 1” and “Send 2” settings that

follow the last IFX in the chain will be used.

Pan(CC#8) (Post IFX PanCC#8)

[L000...C064...R127]

Sets the pan after the sound has passed through the insert
effect. This setting is valid only when the following “BUS
Select” is set to L/R (

☞

p.209).

CC#8 will control the pan of the sound after it has
passed through the insert effect.

8–1

8–2a

Chain