background image

 

 

 

 
 

 

Page 3

 

INTRODUCTION 

Congratulations on your purchase of a biomassfired heating system from KOZLUSAN HEATING 

SYSTEMS. 

With proper installation and maintenance, your heating system will provide years of non-polluting, low cost 

heat for your home.  

To insure correct installation and safe operation of your KOZLUSAN biomass heating system, you should: 

 

Hire a licensed heating contractor

 to install the biomass heating system and integrate it with your 

heating system. This contractor should have experience with installation and operation of gas, oil, 

and solid fuel heating appliances and be familiar with local building codes, fire codes and other 

regulations.  

 

Read this manual

 and learn how to safely operate and maintain your KOZLUSAN biomass heating 

system. 

 

The assembling and start up (setting) of KOZLUSAN biomass boiler has to be carried out by 

our own customer service or by authorized qualified technicians. 

 

 

Do not use any other fuels than specified below: 

 

Ö-Norm M 7135 

 

DIN-PLUS Norm 

 

SWISSPELLET 

 

Diameter: 6 mm   Length: 5-30 mm (20% - 45 mm) 

Only this way low-emission, economical and reliable operation can be guaranteed. Any disregard of 

these requisites leads to immediate expiry of warranty. 

 

The pellets must be stored in dry conditions to enable them to be transported without problems and 

to achieve trouble-free operation with optimum combustion combined with the greatest possible 

efficiency. 

 

We do not assume any liability for unauthorized technical modifications, and resulting damages are 

not covered by warranty. 

 

Operational procedures or alterations of any sort, carried out by unauthorized persons, as well as 

disregarding the general guidelines and the indicated safety instructions as specified here, result in 

immediate termination of all warranty claims. 

 

Please read the safety instructions below before operating the system. Disregarding the safety 

instructions may lead to injuries, perilous situations or damage the pellet boiler. 

Summary of Contents for SLIMPEL






















Reviews: