Instruction manual
www.
kraftool.hk
www.
kraftool.hk
Electric spray gun
|
|
8
9
After each use,
PLEASE RINSE
the product
according to the Operating Procedure.
Periodically clean dirt and dust from the case and
cable, and ventilation openings.
All maintenance work must be carried out with
the cable disconnected from the network.
The product does not require
an
other special
service.
All repair work should be carried out only by
specialists of service centers.
Keep the Product in good condition. In the event
of suspicious odors, smoke, fire, sparks, turn off
the device, disconnect it from the power supply
and contact a specialized service center.
If something seems to you abnormal in the
operation of the Product, immediately stop the
operation.
Due to the technical complexity of the product,
the criteria for limit states cannot be determined
by the users on their own. In case of obvious or
suspected malfunction, refer to the section
“Possible faults and elimination methods”. If you
do not find the fault in the list or cannot
eliminate it, contact a specialized service
center.
The
service
center
issues
a
conclusion on the limiting condition of the Product
or its parts in the form of the relevant Act.
Safety
Instructions
The outcoming jet is a source of potential
danger. To avoid accidents:
`
do not direct the stream at people,
animals
or
at
your
own
body;
` do not direct the jet to electrical outlets, cables,
any electrical and electronic devices;
`
do not put your hands under the nozzle in order
to check the presence or pressure of the jet;
`
do not use damaged nozzles that allow material
to leak;
`
Do not perform any maintenance on the
product or replace the failed parts without
disconnecting it from the mains.
This product is intended to work only with
the materials mentioned above
in the manual
.
DO NOT USE
the product for spraying other
liquids (detergents, technical liquids, flammable
compounds, aggressive solutions, etc.), including
flammable materials with an ignition temperature
less than 35 ° С, as well as liquids whose
properties are unknown to you.
DO NOT LEAVE
flammable materials
unclosed after use (dilution, refueling, at the
end of the work) - this may cause self-ignition.
DO NOT OPERATE
in
rooms
with
high temperature, near hot objects and
sources
of
an
open
fire.
DO NOT SMOKE
during preparing the
materials,
filling
the
container
and
operation.
ALWAYS
use
the
protection
equipment specified at page 9. The materials
sprayed by the Product form a cloud around
the operator and can cause damage to open
parts of the body
and
respiratory
organs.
Ensure your safety when spraying pure
solvent (it can be combustible, corrosive to
open body parts or its vapors are not safe for
breathing).
Warranty
We constantly care about improving the quality of
service to our customers, therefore, if you have
any complaints about the quality and the period of
warranty repair, please, let us know in the
ZUBR support service by e-mail to cs@kraftool.hk.
We provide a warranty for the ZUBR tools under
the following conditions:
1)
The warranty is provided in accordance with
the
conditions listed below by free of
charge
troubleshooting
the
instrument
during the
prescribed warranty period, which is
proved due to
defects in material or workmanship.
2)
The warranty period starts from the date
of
purchase of the instrument by the first owner.
3)
The terms and conditions of the
warranty
depend on the series and article
number of the
instrument, we ask you to
carefully read the
warranty terms at the time of
purchase.
The warranty period is 6 months from the date
of sale.
4) Warranty does not cover:
a)
Parts subject to working and other types of
normal wear and tear, as well as
an
equipment
malfunction caused by these types of
wear, and
the product, which has the full
development of the
resource, strong external or
internal pollution.
b)
Tool malfunctions caused by non-compliance
with the Operating Instructions or occurring due to
misuse of the tool, during use in environmental
conditions beyond the specified operating
instructions, inadequate working conditions, due
to
overloading or insufficient, inadequate
maintenance
or care. The unconditional signs of
product
overload include, among others, the
appearance of
colors of tinge, simultaneous
failure of the rotor and
stator, deformation or
melting of parts and
components of the product,
darkening or charring of
the electric motor wires
under the action of high
temperature.
c)
When using the product in conditions of high
intensity work and super heavy loads.
d)
For preventive and maintenance works, for
example: lubrication, flushing.
e)
Tool malfunctions due to the use of
accessories, associated and spare parts that are
not original accessories/parts of the ZUBR.
f)
Mechanical damage (cracks, chips, etc.) and
damage caused by exposure to corrosive
environments, high temperature and high
humidity, the ingress of foreign objects into the
ventilation opening tool and also damage caused
by improper storage and corrosion of metal parts.
g)
Accessories, wear parts and consumables that
failed due to normal wear, such as drive belts,
battery packs, barrels, guide rollers, protective
covers, collets, cartridges, soles, saw chains, saw
tires, sprockets, tires, carbon brushes, knives,
sawing, abrasives, drills, trimmer line, etc.
h)
The tool, the design of which has been
amended or supplemented.
i)
Insignificant deviation from the declared
properties of the instrument, which does not
affect
its value and the possibility of its intended
use.
j)
For a tool that has been opened or revised
during the warranty period outside of authorized
service centers.
5)
The elimination of faults recognized by us as a
warranty case is carried out at the choice of
the
ZUBR
company by repairing or replacing the
product with
a new one (possibly with a next
-
generation model).
Replaced product and its
parts become the
property of the company.
6)
Warranty claims are accepted within the
warranty period. To do this, submit or send the
defective instrument to the service center,
enclosing the completed warranty certificate
confirming the date of purchase of the goods and
its name. A product transferred to a dealer or
service center in a partially or fully disassembled
form is not covered by the warranty. All risks of
transferring and shipping the product to the dealer
or service center are borne by the product owner.
7)
Other claims, other than the said right to
a
free
repair of the defects of the instrument, are
not
covered by the warranty.
8)
All power tools require regular
maintenance.
The maintenance interval is equal
to the service life of the carbon brush set.
9) 9) The service life of the product is 5 years.