KRAFTtech PS160CA-3 Owner'S Manual Download | Manualshive

Page: 7 / 12

background image

ASSEMBLY

3. After inserting the sandpaper, release pressure on clamp lever making sure that the

clamp is gripping the sandpaper and the sandpaper is aligned with the pad.

4. Wrap the sandpaper around the bottom of the pad, and attach the free end of

sandpaper under the opposite clamp, repeating procedures 1, 2 & 3, above.

KRAFTtech

PS160CA-3

Page 7

FIG. 3

CLAMP LEVER

PAD

SANDPAPER

«
...
5
6
7
8
9
...
»

Summary of Contents for PS160CA-3













Reviews:

No comments

Related manuals for PS160CA-3

Brand: Jet Pages: 22

Brand: Domanoff Pages: 4

Brand: King Industrial Pages: 5

5 IN. BRUSHLESS RANDOM ORBIT SANDER

Brand: Kobalt Pages: 28

Brand: Powermate Pages: 16

Brand: Craftex Pages: 14

Brand: Craftex Pages: 24

Brand: Skil Pages: 108

Brand: Milwaukee Pages: 8

Brand: Milwaukee Pages: 20

Brand: HSS Hire Pages: 2

Brand: Record Power Pages: 20

Brand: Power Fist Pages: 32

Brand: Galeski Pages: 8

Brand: laguna Pages: 82

Brand: Parkside Pages: 34

Brand: EINHELL Pages: 177

Brand: Makita Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands