KRAFTtech PS160CA-3 Owner'S Manual Download | Manualshive

Page: 8 / 12

background image

ASSEMBLY

ATTACHING THE DUST BAG

Align the groove in the dust bag assembly with the groove in the vacuum port (see FIG. 4),
and then press down on the dust bag assembly to lock it in place.

OPERATION INSTRUCTIONS

SANDPAPER

This 1/4 sheet sander is designed to be used with standard, commercially available sandpa-
per sheets. Cut the sheet crosswise into quarters for a precise fit.

Aluminum oxide, silicon carbide, or other synthetic abrasives are recommended for power
sanding use. For rough sanding, sandpaper with a coarse grit is best. For smoothing or final
sanding, sandpaper with a fine or extra-fine grit should be used.

TM

FIG. 4

KRAFTtech

PS160CA-3

Page 8

«
...
6
7
8
9
10
...
»

Summary of Contents for PS160CA-3













Reviews:

No comments

Related manuals for PS160CA-3

Brand: Oliver Pages: 50

Brand: Rac Pages: 4

Brand: Ryobi Pages: 10

Brand: PEUGEOT Pages: 34

Brand: Virutex Pages: 20

Brand: Clarke Pages: 16

Brand: Emax Pages: 8

Brand: Meec tools Pages: 39

Brand: Nordic Pages: 12

Brand: Nordic Pages: 16

Brand: Powermatic Pages: 28

Brand: Casals Pages: 52

Brand: Universal Tool Pages: 8

Brand: Aeropro Pages: 4

Brand: Flex Pages: 26

Brand: HOLZMANN MASCHINEN Pages: 37

Brand: HOLZMANN MASCHINEN Pages: 50

Brand: HOLZMANN MASCHINEN Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands