Kramer 908 User Manual Download

Page: 27 / 32

908 - 908 Commands in Protocol 3000

9.8

Network Setting Commands

Command

Syntax

Response

Set IP address

NET-IP IP_ADDRESS
Short form: NTIP

NET-IP IP_ADDRESS RESULT

Read IP address

NET-IP?
Short form: NTIP?

NET-IP IP_ADDRESS

Read MAC address

NET-MAC?
Short form: NTMC

NET-MAC MAC_ADDRESS

Set subnet mask

NET-MASK SUBNET_MASK
Short form: NTMSK

NET-MASK SUBNET_MASK RESULT

Read subnet mask

NET-MASK?
Short form: NTMSK?

NET-MASK SUBNET_MASK

Set gateway address NET-GATE GATEWAY_ADDRESS

Short form: NTGT

NET-GATE GATEWAY_ADDRESS

RESULT

Read subnet mask

NET-GATE?
Short form: NTGT?

NET-GATE GATEWAY_ADDRESS

Set DHCP mode

NET-DHCP DHCP_MODE
Short form: NTDH

NET-DHCP DHCP_MODE RESULT

Read subnet mask

NET-DHCP?
Short form: NTDH?

NET-DHCP DHCP_MODE

DHCP_MODE =

‘0’ – Don't use DHCP (Use IP set by factory or IP set command).
‘1’ – Try to use DHCP, if unavailable use IP as above.

Change protocol
Ethernet port

ETH-PORT PROTOCOL , PORT
Short form: ETHP

ETH-PORT PROTOCOL ,PORT

RESULT

Read protocol
Ethernet port

ETH-PORT? PROTOCOL
Short form: ETHP?

ETH-PORT PROTOCOL , PORT

PROTOCOL = TCP/UDP (transport layer protocol)

PORT = Ethernet port that accepts Protocol 3000 commands

1-65535 = User defined port
0 - Reset port to factory default (50000 for UDP, 5000 for TCP)

9.9

Machine Information Commands

Command

Syntax

Response

Set device time and date

TIME DATE_TIME

TIME DATE_TIME RESULT

Read device time and date TIME?

TIME? DATE_TIME

Note

: Time setting commands require administrator authorization.

Read in/out count

INFO-IO?

INFO-IO: IN INPUTS_COUNT, OUT

OUTPUTS_COUNT

Read max preset count

INFO-PRST?

INFO-PRST: VID

PRESET_VIDEO_COUNT , AUD
PRESET_AUDIO_COUNT

Execute firmware upgrade* UPGRADE

UPGRADE OK

Firmware usually uploads to a device via a command like LDFW. The device may need to be reset to
complete the process.

Summary of Contents for 908

































Search results

Summary of Contents for 908

Reviews:

Related manuals for 908

Brands by name

Popular brands

Kramer 908, User Manual

Search results

Summary of Contents for 908

Reviews:

Related manuals for 908

Brands by name

Popular brands