background image

PT-571HDCP/PT- - Getting Started 

2.3 

Recycling Kramer Products 

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC 

aims to reduce the amount of WEEE sent for disposal to landfill or incineration by 

requiring it to be collected and recycled. To comply with the WEEE Directive, 

Kramer Electronics has made arrangements with the European Advanced 

Recycling Network (EARN) and will cover any costs of treatment, recycling and 

recovery of waste Kramer Electronics branded equipment on arrival at the EARN 

facility. For details of Kramer’s recycling arrangements in your particular country 

go to our recycling pages  

2.4 

Accessory to Medical Equipment (IEC 60601-1-2) 

In the modern medical environment remote access is essential, for example, to 

transfer clinical data between doctors and to train to medical students. The 

PT-571HDCP/PT-

 pair is certified according to the IEC 60601-1-2, 

Clause 2.1.3, Medical Electrical Equipment, Part 1: General Requirements for 

EMC standard which is required when accessory devices are used at locations 

where medical personnel and patients are present. 

The 

PT-571HDCP/PT-

 pair constitutes an optional component that can 

be considered necessary and suitable as part of medical equipment or for use as 

part of a medical system to provide real time simultaneous video feeds to those 

present at the local medical environment and at remote locations. In this 

environment, the 

PT-571HDCP/PT-

 can be added to the system ONLY 

if the connecting equipment has been evaluated and meets the IEC 60601-1-2 

EMC standards. Note, that when attaching accessory devices to a digital or 

analog interface, they must comply with the IEC standard for which they are used: 

EMC Standard (IEC 60601-1-2), Information Technology equipment (IEC 60950-1 

(2ed)). 

Summary of Contents for PT-571HDCP

















Reviews: