background image

Connecting the VS-81SP 8 x 1 Loudspeaker Switcher 

 

13 

13 

6.3.2  Setting the MACHINE ADDRESS # 

For certain applications, you may need more than 8 outputs

1

Table 4: MACHINE ADDRESS # DIP-switch Settings 

. Cascading the 

outputs enables you to expand the number of outputs by looping up to seven 
units to form a combined speaker switcher with up to 50 speaker pair 
outputs.  

MACHINE # 

DIP 1 

DIP 2 

DIP 3 

DIP 4 

ON 

OFF 

OFF 

OFF 

OFF 

ON 

OFF 

OFF 

ON 

ON 

OFF 

OFF 

OFF 

OFF 

ON 

OFF 

ON 

OFF 

ON 

OFF 

OFF 

ON 

ON 

OFF 

ON 

ON 

ON 

ON 

To cascade up to seven identical units:

 

 

Set the same MACHINE # on each unit, according to 

Table 3

 

 

Set the MACHINE ADDRESS # and the eighth DIP-switch (last 
in daisy-chain) on each unit that is included in a set, according to 

Table 4

 

Figure 8

 and 

Figure 9

 give an example of how to setup and address a 

cascade of three 

VP-81SP

 units that output to 22 speaker pairs. 

 

                                                       

 

1 You can also use this procedure for cascading inputs as well as outputs 

Summary of Contents for VS-81SP

































Reviews: