background image

Page 

10

 of 

19

 

 

APPLIANCE INSTALLATION 

 

Remove Packaging Materials 

IMPORTANT: 

Do not remove any permanent instruction labels or the data label on your 

appliance

.

 

 

Remove tape and glue from your 

appliance

 before using.

 

 

To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be 

easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with 

warm water and dry with a soft cloth.

 

 

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. 

These products can damage the surface of your 

appliance

.

 

 

NOTICE: 

LOSS OR SPOILAGE OF PRODUCTS IN YOUR APPLIANCE IS NOT COVERED BY WARRANTY. IN ADDITION TO 

FOLLOWING RECOMMENDED INSTALLATION PROCEDURES. PLEASE RUN THE APPLIANCE 24 HOURS PRIOR 

TO USAGE. 

 

Location Requirements 

 

Appliances represented in this manual are intended for indoor use only. 

 

Be sure the location chosen has a floor strong enough to support the total weight of the cabinet and contents as a fully 

loaded unit can weigh as much as 800 pounds. 

 

Reinforce the floor as necessary to provide for maximum loading. 

 

For the most efficient refrigeration, be sure to provide good air circulation inside and out. 

 

Inside cabinet: 

Do not pack the units so full that air cannot circulate. The refrigerated air is discharged at the top rear of the unit. It is 

important to allow for proper air flow from the top rear to the bottom of the unit. Obstructions to this air flow can cause 

evaporator coil freeze ups and loss of temperature or overflow of water from the evaporator drain pan. The shelves have a 

rear turn up on them to prevent this. However, bags and other items can still be located to the far rear of the cabinet. 

Air is 

brought into the evaporator coil with fans mounted to the front of the coil. 

 

Outside cabinet:

 

Be sure that the unit has access to ample air. Avoid hot corners and locations near stoves and ovens. 

It is recommended that the unit be installed no closer than 2" (51mm) from any wall, and a max door swing clearance of 

60.5 in (1537mm). 

 

 

 

    WARNING    

 

Excessive Weight Hazard

 

Use two or more persons to move and install 

appliances

Failure to do so may result in back or other injury.

 

Summary of Contents for 69K-762




















Reviews: