Kreg FOREMAN DB210 Owner'S Manual Download

Page: 31 / 44

Seguridad

Manipule con cuidado las guías para taladro y mantenga las manos

alejadas cuando estén instaladas en la máquina.

El espacio mínimo

requerido entre la broca y la guía para taladro para mejorar la calidad del

orificio produce un borde afilado que puede suponer un riesgo de laceración.

Mantenga las manos alejadas de la broca giratoria y de la abrazadera

de la pieza de trabajo mientras opere la máquina.

Asegúrese de que la broca esté completamente separada de la pieza

de trabajo y que se detenga completamente antes de regular la posición

de la pieza de trabajo.

Asegure la máquina para evitar inclinaciones o deslices.

No se pare

sobre la máquina.

Siga todas las prácticas de lubricación y mantenimiento que se

detallan en el manual de instrucciones.

Esta máquina está diseñada para una aplicación específica. No la

modifique ni la use para otra aplicación.

Si tiene preguntas relacionadas con

la aplicación de la máquina, NO la use hasta ponerse en contacto con Kreg Tool

Company y recibir la orientación correspondiente.

En la etiqueta de su máquina pueden aparecer los siguientes símbolos.

TLos símbolos y sus definiciones son los siguientes:

Propuesta 65 de California

Especificaciones del motor Foreman DB210

120 V~5.0A 2800 rpm

Pautas para el uso de extensiones eléctricas

Las extensiones eléctricas son solo para uso temporal. No reemplazan

la necesidad de instalar tomacorrientes y cableado adecuado donde sea

necesario.

En el taller y en sitios de construcción:

1. Se deben usar extensiones eléctricas con conductor de puesta a tierra del

equipo en todo momento.

2. Las extensiones eléctricas deben protegerse de daños y no deben tenderse

a través de puertas o ventanas, ya que estas puedan cerrarse y dañar el cable.

3. Las extensiones eléctricas deben ser de 16 AWG como mínimo y tener una

clasificación adecuada para el equipo que se utiliza.

4. Las extensiones eléctricas deben inspeccionarse periódicamente para

controlar que el aislamiento y la conductividad no se vean comprometidos.

5. Las extensiones eléctricas no deben tenderse sobre agua, y no se debe

permitir que las conexiones estén expuestas a agua acumulada.

Calibre de la extensión

eléctrica

Largo de la extensión eléctrica

Placa de datos:

amperios a120 V

7,62 m 15,24 m 22,86 m 30,48 m 45,72 m 60,96 m

0 - 5

5.1 - 8

8.1 -12

12.1 - 16

NR: no recomendado

TABLA 1

símbolo de alerta de seguridad

voltios

hercios

amperios

vatios

corriente continua

corriente alterna

corriente alterna o continua

Clase I para construcción

(con puesta a tierra)

Clase II para construcción

(con doble aislamiento)

terminal de tierra

minutos

por minuto

golpes por minuto

revoluciones por minuto

velocidad sin carga

min

/min

BPM

RPM

English

• Be sure that the cutter knives are mounted as described in the

instruction manual and check that all bolts are firmly tightened

before connecting unit to power source.

• To avoid injury, never rotate the cutter block directly with your

hands.

• Keep guards in place and in good working order.
• Stay alert – never operate the unit when tired or under the

influence of drugs, alcohol, or medication.

• Do not use in dangerous environments. Do not use near

flammable substances, in damp or wet locations, or expose to

rain.

• Never plane material which is shorter than 12 inches.
• Exhaust chute: remove shavings with brush or vacuum after

power has been shut off and cutter head has stopped rotating.

• ALWAYS LOCATE PLANER WITH PROPER CLEARANCE ON

THE OUTFEED SIDE of the unit to prevent pinching or binding of

the workpiece against any obstacle.

•

Clean out your tool often, especially after heavy use.

Dust

and grit containing metal particles often accumulate on interior

surfaces and could create a risk of serious injury, electric shock or

electrocution. ALWAYS WEAR SAFETY GLASSES.

WARNING:

For your own safety, it is recommended that two

people carry this machine or serious injury could result.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use.

Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

WARNING:

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

•

crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.
•

Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water.

Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING:

A dust mask or respirator should be worn by all

persons entering the work area. The filter should be replaced daily or

whenever the wearer has difficulty breathing. See your local hardware

store for the proper NIOSH/OSHA approved dust mask.
• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ......... volts

A .......amperes

Hz ....... hertz

W ......watts

min ..... minutes

.....alternating current

... direct current

.....alternating or direct current

....... Class I Construction

no ......no load speed

...........

(grounded)

......earthing terminal

....... Class II Construction

.....safety alert symbol

...........

(double insulated)

BPM ..beats per minute

…/min per minute

RPM ..revolutions per minute

English

• Be sure that the cutter knives are mounted as described in the

instruction manual and check that all bolts are firmly tightened

before connecting unit to power source.

• To avoid injury, never rotate the cutter block directly with your

hands.

• Keep guards in place and in good working order.
• Stay alert – never operate the unit when tired or under the

influence of drugs, alcohol, or medication.

• Do not use in dangerous environments. Do not use near

flammable substances, in damp or wet locations, or expose to

rain.

• Never plane material which is shorter than 12 inches.
• Exhaust chute: remove shavings with brush or vacuum after

power has been shut off and cutter head has stopped rotating.

• ALWAYS LOCATE PLANER WITH PROPER CLEARANCE ON

THE OUTFEED SIDE of the unit to prevent pinching or binding of

the workpiece against any obstacle.

•

Clean out your tool often, especially after heavy use.

Dust

and grit containing metal particles often accumulate on interior

surfaces and could create a risk of serious injury, electric shock or

electrocution. ALWAYS WEAR SAFETY GLASSES.

WARNING:

For your own safety, it is recommended that two

people carry this machine or serious injury could result.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use.

Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

WARNING:

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

•

crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.
•

Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water.

Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING:

A dust mask or respirator should be worn by all

persons entering the work area. The filter should be replaced daily or

whenever the wearer has difficulty breathing. See your local hardware

store for the proper NIOSH/OSHA approved dust mask.
• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ......... volts

A .......amperes

Hz ....... hertz

W ......watts

min ..... minutes

.....alternating current

... direct current

.....alternating or direct current

....... Class I Construction

no ......no load speed

...........

(grounded)

......earthing terminal

....... Class II Construction

.....safety alert symbol

...........

(double insulated)

BPM ..beats per minute

…/min per minute

RPM ..revolutions per minute

English

• Be sure that the cutter knives are mounted as described in the

instruction manual and check that all bolts are firmly tightened

before connecting unit to power source.

• To avoid injury, never rotate the cutter block directly with your

hands.

• Keep guards in place and in good working order.
• Stay alert – never operate the unit when tired or under the

influence of drugs, alcohol, or medication.

• Do not use in dangerous environments. Do not use near

flammable substances, in damp or wet locations, or expose to

rain.

• Never plane material which is shorter than 12 inches.
• Exhaust chute: remove shavings with brush or vacuum after

power has been shut off and cutter head has stopped rotating.

• ALWAYS LOCATE PLANER WITH PROPER CLEARANCE ON

THE OUTFEED SIDE of the unit to prevent pinching or binding of

the workpiece against any obstacle.

•

Clean out your tool often, especially after heavy use.

Dust

and grit containing metal particles often accumulate on interior

surfaces and could create a risk of serious injury, electric shock or

electrocution. ALWAYS WEAR SAFETY GLASSES.

WARNING:

For your own safety, it is recommended that two

people carry this machine or serious injury could result.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use.

Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

WARNING:

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

•

crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.
•

Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water.

Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING:

A dust mask or respirator should be worn by all

persons entering the work area. The filter should be replaced daily or

whenever the wearer has difficulty breathing. See your local hardware

store for the proper NIOSH/OSHA approved dust mask.
• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ......... volts

A .......amperes

Hz ....... hertz

W ......watts

min ..... minutes

.....alternating current

... direct current

.....alternating or direct current

....... Class I Construction

no ......no load speed

...........

(grounded)

......earthing terminal

....... Class II Construction

.....safety alert symbol

...........

(double insulated)

BPM ..beats per minute

…/min per minute

RPM ..revolutions per minute

English

• Be sure that the cutter knives are mounted as described in the

instruction manual and check that all bolts are firmly tightened

before connecting unit to power source.

• To avoid injury, never rotate the cutter block directly with your

hands.

• Keep guards in place and in good working order.
• Stay alert – never operate the unit when tired or under the

influence of drugs, alcohol, or medication.

• Do not use in dangerous environments. Do not use near

flammable substances, in damp or wet locations, or expose to

rain.

• Never plane material which is shorter than 12 inches.
• Exhaust chute: remove shavings with brush or vacuum after

power has been shut off and cutter head has stopped rotating.

• ALWAYS LOCATE PLANER WITH PROPER CLEARANCE ON

THE OUTFEED SIDE of the unit to prevent pinching or binding of

the workpiece against any obstacle.

•

Clean out your tool often, especially after heavy use.

Dust

and grit containing metal particles often accumulate on interior

surfaces and could create a risk of serious injury, electric shock or

electrocution. ALWAYS WEAR SAFETY GLASSES.

WARNING:

For your own safety, it is recommended that two

people carry this machine or serious injury could result.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use.

Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

WARNING:

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

•

crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.
•

Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water.

Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING:

A dust mask or respirator should be worn by all

persons entering the work area. The filter should be replaced daily or

whenever the wearer has difficulty breathing. See your local hardware

store for the proper NIOSH/OSHA approved dust mask.
• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ......... volts

A .......amperes

Hz ....... hertz

W ......watts

min ..... minutes

.....alternating current

... direct current

.....alternating or direct current

....... Class I Construction

no ......no load speed

...........

(grounded)

......earthing terminal

....... Class II Construction

.....safety alert symbol

...........

(double insulated)

BPM ..beats per minute

…/min per minute

RPM ..revolutions per minute

English

• Be sure that the cutter knives are mounted as described in the

instruction manual and check that all bolts are firmly tightened

before connecting unit to power source.

• To avoid injury, never rotate the cutter block directly with your

hands.

• Keep guards in place and in good working order.
• Stay alert – never operate the unit when tired or under the

influence of drugs, alcohol, or medication.

• Do not use in dangerous environments. Do not use near

flammable substances, in damp or wet locations, or expose to

rain.

• Never plane material which is shorter than 12 inches.
• Exhaust chute: remove shavings with brush or vacuum after

power has been shut off and cutter head has stopped rotating.

• ALWAYS LOCATE PLANER WITH PROPER CLEARANCE ON

THE OUTFEED SIDE of the unit to prevent pinching or binding of

the workpiece against any obstacle.

•

Clean out your tool often, especially after heavy use.

Dust

and grit containing metal particles often accumulate on interior

surfaces and could create a risk of serious injury, electric shock or

electrocution. ALWAYS WEAR SAFETY GLASSES.

WARNING:

For your own safety, it is recommended that two

people carry this machine or serious injury could result.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use.

Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

WARNING:

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

•

crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.
•

Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water.

Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING:

A dust mask or respirator should be worn by all

persons entering the work area. The filter should be replaced daily or

whenever the wearer has difficulty breathing. See your local hardware

store for the proper NIOSH/OSHA approved dust mask.
• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ......... volts

A .......amperes

Hz ....... hertz

W ......watts

min ..... minutes

.....alternating current

... direct current

.....alternating or direct current

....... Class I Construction

no ......no load speed

...........

(grounded)

......earthing terminal

....... Class II Construction

.....safety alert symbol

...........

(double insulated)

BPM ..beats per minute

…/min per minute

RPM ..revolutions per minute

English

• Be sure that the cutter knives are mounted as described in the

instruction manual and check that all bolts are firmly tightened

before connecting unit to power source.

• To avoid injury, never rotate the cutter block directly with your

hands.

• Keep guards in place and in good working order.
• Stay alert – never operate the unit when tired or under the

influence of drugs, alcohol, or medication.

• Do not use in dangerous environments. Do not use near

flammable substances, in damp or wet locations, or expose to

rain.

• Never plane material which is shorter than 12 inches.
• Exhaust chute: remove shavings with brush or vacuum after

power has been shut off and cutter head has stopped rotating.

• ALWAYS LOCATE PLANER WITH PROPER CLEARANCE ON

THE OUTFEED SIDE of the unit to prevent pinching or binding of

the workpiece against any obstacle.

•

Clean out your tool often, especially after heavy use.

Dust

and grit containing metal particles often accumulate on interior

surfaces and could create a risk of serious injury, electric shock or

electrocution. ALWAYS WEAR SAFETY GLASSES.

WARNING:

For your own safety, it is recommended that two

people carry this machine or serious injury could result.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use.

Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

WARNING:

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or

other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

•

crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.
•

Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water.

Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING:

A dust mask or respirator should be worn by all

persons entering the work area. The filter should be replaced daily or

whenever the wearer has difficulty breathing. See your local hardware

store for the proper NIOSH/OSHA approved dust mask.
• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ......... volts

A .......amperes

Hz ....... hertz

W ......watts

min ..... minutes

.....alternating current

... direct current

.....alternating or direct current

....... Class I Construction

no ......no load speed

...........

(grounded)

......earthing terminal

....... Class II Construction

.....safety alert symbol

...........

(double insulated)

BPM ..beats per minute

…/min per minute

RPM ..revolutions per minute

Advertencia:

este producto puede exponerlo a sustancias químicas, que

incluyen el plomo, reconocidas por el estado de California como causantes de

cáncer y defectos congénitos u otros daños en el aparato reproductivo. Para obtener

más información, viste www.P65Warnings.ca.gov.

Advertencia:

este producto puede exponerlo a sustancias químicas,

que incluyen el plomo, entre otras, reconocidas por el estado de California como

causantes de cáncer y defectos congénitos u otros daños en el aparato reproductivo.

Para obtener más información, viste www.P65Warnings.ca.gov.

Advertencia:

los productos para taladrar, aserrar, lijar o cortar madera

pueden exponerlo al polvo de madera, una sustancia reconocida por el estado de

California como causante de cáncer. Evite inhalar el polvo de la madera o utilice

una mascarilla antipolvo u otros artículos de protección personal. Para obtener más

información, viste www.P65Warnings.ca.gov.

Summary of Contents for FOREMAN DB210













































Search results

Summary of Contents for FOREMAN DB210

Reviews:

Related manuals for FOREMAN DB210

Brands by name

Popular brands

Kreg FOREMAN DB210, Owner'S Manual

Search results

Summary of Contents for FOREMAN DB210

Reviews:

Related manuals for FOREMAN DB210

Brands by name

Popular brands