KRONAsteel KAMILLA, Application Sheet

LV  Lietošanas instrukcija

8

EN  Application sheet

KITCHEN HOODS

2.     Install the plug from the kit to the upper air out-

let of the kitchen hood.

3.    Turn the mode switch (located on the plastic 

box of the motors inside the hood) to the posi-

tion in which the arrow in the figure of the house 

points inside.

When using the hood in the mode of air exhaust to 

the ventilation shaft, you should:

1.     Remove the plug from the upper air outlet of the 

hood.

2.    Replace it with the adapter flange from the sup-

ply kit.

3.   Turn the mode switch (located on the plastic 

box of the motors inside the hood) to the posi-

tion where the arrow in the figure of the house 

points out.

4.    Fix to the adapter flange an air duct of 150 mm 

diameter and required length with a clamp 

(available separately).

Installation of the kitchen hood  

to the wall

When attaching the hood to the wall (Fig. 14) opera-

tions are performed in the following sequence: 

1.     Make a layout before drilling holes for mounting 

the hood to the wall.  To do this, it is necessary 

to measure the distance between the centers of 

the holes intended for hanging on the wall.  At 

the desired height draw a horizontal line on the 

wall. Mark the points A and B on this line, the 

distance between the points should be equal to 

the distance measured between the centers of 

the holes for hanging the hood. 

2.    Drill 2 holes at the points marked on the wall. 

The depth and diameter of the holes must 

match the size of the dowels from the mounting 

kit.

3.    Install the dowels in the holes you have drilled.  

Screw the screws into the dowels so that the 

distance between the wall and the head of the 

screw is approximately 5 mm.

4.    Hang the hood on the support points.

Installation of a hood to a wall cabinet

1.    There are four holes in the upper part of the 

machinehood housing with metal bushings in-

serted into. These holes are used to fix the hood 

to the hanging cabinet (Fig. 15).

2.    The hanging cabinet is ordered, as a rule, with-

out a bottom, and the middle shelf is placed at 

a given height relative to the lower edge of the 

cabinet so that the machine body is recessed 

into the Cabinet.

3.    With the use of sampler (placed with the manu-

al into the packaging of the machine) the layout 

for the holes for the screws and a flexible air 

duct are made on the middle shelf of the cabi-

net (if the machine is used in the mode of air 

exhaust to the shaft).

4.    With the use of sampler mark the ceiling of the 

cabinet for fixing the flexible air duct (if the hood 

is used in the mode of air exhaust to the shaft).

5.   In the middle shelf the holes for screws are 

drilled, and, in addition, in the middle shelf and 

the ceiling of the cabinet the holes for the flex-

ible air duct are made (if the hood is used in the 

mode of air exhaust to the shaft).

6.    Before placing the hood in the cabinet chose 

the desired mode of use and make the changes 

described in the instructions above.

7.    The hood is fixed with screws to the middle 

shelf of the cabinet, then its upper part is re-

cessed into the cabinet.

8.    After the hood is mounted in the cabinet, the 

latter is suspended on the wall of the kitchen.

CONNECTION TO POWER SUPPLY

The kitchen hood is connected to the power net-

work with the voltage of 220-240V, 50 Hz.

The kitchen hood should be connected to a wall 

outlet with earthing to avoid electrocution.

It is absolutely prohibited to cut off the plug 

during kitchen hood installation.

The damaged electrical cord should be re-

placed by a qualified service specialist.

For additional protection of the kitchen hood from 

voltage drops in the network, connect it though an 

additional automatic switch 6A.

The kitchen hood is installed.

Switch it on and use it as you please.