background image

11 

INTRODUCTION 

This manual is an integral part of the 
appliance  and  it  contains  all  the 
necessary 

information 

for 

its 

operation and maintenance. The user 
must  read  it  carefully  before  starting 
the appliance. 

ORIGINAL INSTRUCTION 

The  text  was  scrupulously  revised,  however,  any 
eventual  printing  mistake  should  be  indicated  to  the 
manufacturer.  Moreover,  in  order  to  improve  the 
product  we  reserve  the  right  to  modify  and  update  this 
publication  without  notice.  Any  reproduction  of  this 
manual,  even  partial,  is  forbidden  without  the 
authorization of the manufacturer. 

INTENDED USE 

Professional steam generator: 

This appliance is to be used in the inside. The functions 
provided  for  this appliance  are  exclusively  the  cleaning 
of  floor  and  washable  surfaces  compatible  with  steam, 
textiles  included;  (not  to  be  used  on  electrified 
parts).Any  other  use  other  than  that,  it  is  to  be 
considered unauthorized and dangerous. 

IDENTIFICATION AND TECHNICAL DATA 

On the label attached on the back of the machine, you 
can find the technical specification shown in the chart 
below:

 

Model: 

KGVC 

4000

 

Electric power supply  

220V - 230V  50Hz 

Max power  

3.6kW 

Steam pressure  

1000kPa (10 bar) 

Steam production 

80÷95 g/min. 

Boiler capacity   

3.5l 

Heating time  

6 min. 

Acceptable pressure  

1200kPa (12bar) 

Steam max temperature 

185°C 

Boiler max power  

3.3kW 

Boiler material   

inox Aisi 304 

Weight   

38kg 

Dimensions  LxPxH  

780x510x1000mm 

Tolerated water conductivity 

80÷1500uS/cm (4÷75 °f) 

Water tank  

5l 

Detergent tank  

5l 

Vacuum bucket 

10l 

Vacuum motor By-pass 2 st.  

(1200-1400W) 

max. 175 m³/h 

Appliance of class 

I

 

Sound pressure 

76 dB(A) 

SAFETY DEVICES OF THE PRODUCT: 

Two  thermostats:  one  ceramic  thermostat  to  restore 
manually  frontal  to  the  boiler,  one  bulb  thermostat 
inserted  in  the  tube  between  the  resistances,  it  begins 
to  work  in  the  event  of  excessive  temperature  or 
anomaly. 

Safety  valve,  it  allows  the  discharge  of  the  steam  in 
excess  in  case  of  anomalous  condition  of  the  machine 
under pressure. If it starts working, turn the machine off 
and  take  it  to  a  maintenance  center  for  a  checkup. 

Low  voltage  in  the  handle  (safety  voltage  used  for 
connection to the inside of the hose). 

  USED SYMBOLS 

GENERAL DANGER: when used, 
this symbol indicates the need to 
carefully pay attention to the 
functions or notes described 
MAINTENANCE: operations and 
maintenance details 

STEAM : attention hot steam jets 

HOT SURFACES: attention burns 

DECOMMISIONING: rules to be 
followed at the end of the product 
life  

DO NOT DIRECT THE JET 
towards persons, animals, electrical 
equipment under pressure or the 
machine itself 

SAFEGUARDS RULES 

- The  Electric  power  connection  must  be  made  by  a
qualified  electrician  and  must  conform  to  IEC  60364-1.
It  is  recommended  that  the  electric  supply  to  this
machine  should  include  a  residual  current  device  that
interrupts  the  power  supply  if  the  leakage  current  to
ground exceeds 30 mA for 30 seconds or a device that
checks the grounding circuit.
- WARNING Children or unqualified persons should not
use the machines.
- The  device  can  be  use  by  persons  with  reduced
physical,  sensory  or  mental  capabilities,  or  lack  of
experience  or  knowledge  as  long  as  they  are  under
surveillance  or  after  having  received  instructions
regarding  the  safe  use  of  the  appliance  and  after  the
comprehension of its dangers.
-Children must not play with the appliance.
- The  appliance  must  be  disconnected  from  the  plug
after use and before the user performs maintenance on
the unit.
- The cleaning and maintenance meant to be performed
by  the  user  should  not  be  made  by  children  without
supervision.
- The  liquid  or steam  must not  be directed  towards  the
devices  which  contain  electrical  components,  such  as
the interior of ovens.
- Do  not  use  in  swimming  pools  when  they  are  full  of
water.
- Do  not  leave  the  device  unattended  when  it  is
connected to the power.
- Do not use the device if it has been dropped, if there
are visible signs of damage or if there are losses.
- Maintain the machine out of  reach of children when it
is used or it is cooling down.

Summary of Contents for KGVC4000





































Reviews: