Kruger KF 675BBC, Manual

32

5.2.2 BATTERY

If supplied, the Pb-Acid (if not dry charged) or gel 

batteries are ready to be installed: 

Positive pole - red

Negative pole - black.

5.2.3 BATTERY 

CHARGER

If supplied, refer to the corresponding booklet.

5.3 BATTERY 

CHARGER 

CONFIGURA-

TION



 We recommend to call the assistance centre or 

a technician if you have problems with the setting 

given. 

The machine is equipped with a battery charger 

configurated for PB-Acid batteries

If the operator whish to use GEL / AFGM batteries, 

it is  necessary change the battery charger settings 

as follows:



 DISPLAY OF THE BATTERY CHARGER SETTINGS

The battery charger settings are shown by the 

blinking of the LED indicator when the battery 

charger is switching on:

- the RED LED indicator ( Photo I - 2 ) flashes 

2 times = the battery charger is set for PB-Acid 

batteries

-  the GREEN LED indicator ( Photo I - 3 ) 

flashes 2 times = the battery charger is set for 

GEL batteries

The battery charger settings will be displayed even 

if batteries are not connected.



  DIP-SWITCH CONFIGURATION FOR BATTERY 

CHARGER CBHD2 24V 20A 

To set the charging curve type for Pb-Acid or 

GEL/AGM batteries it is necessary to operate on 

the dip-switches placed inside the battery 

charger ( Photo I -4 ).

The dip-switches for the setting of the charging 

curve are on the control card ( Photo I - 4 ) that 

is placed behind the lower panel of the battery 

charger ( Photo I - 1 ). It is also possible to reach 

the dip-switches by removing the plastic cap ( 

Photo I - 5 ).

For the setting of the charging curve it is neces-

sary to operate on the dip-switches of the group 

indicated as SW1 ( Photo I - 6 ), placing them 

as shown in the table ( Photo I - 6)  at page 7.

NOTE: The dip-switches of the group indicated as 

SW2 

must always be set in the OFF posi-

tion.

5.4 ACCESSORIES

Your machine supplier can provide a complete and 

updated list of all available accessories, such as 

brushes, pad drivers, disks, etc.

6. INSTALLATION INFORMATION

6.1 BATTERY 

PREPARATION



 The technical features of the batteries used 

must match those indicated in the technical fea-

tures section. Using different batteries may cause 

serious damage to the machine or may require 

them to be charged more frequently.



 During installation or when performing any 

type of battery maintenance, the operator must 

be equipped with adequate safety accessories to 

prevent accidents. Work far from open flames, do 

not short-circuit the battery poles, do not generate 

sparks and do not smoke.

The batteries are normally supplied full of acid so-

lution (for the Pb-Acid type) and ready for use. In 

any case, follow the steps indicated in the manual 

supplied with the battery and carefully follow the 

instructions regarding safety and operating proce-

dures.

6.2 

BATTERY INSTALLATION AND 

PREPARATION



 These operations must be carried out by spe-

cialised personnel.

Make sure the two tanks are empty. If not, empty 

them in accordance with the specific procedure.

Lift the recovery tank by 90°, making sure it is sta-

ble in that position. This provides access to the 

battery compartment from the top.

Disconnect the Anderson connector of the battery 

wiring from the Anderson connector of the machine 

wiring. Always hold the connectors with the hands 

and never pull on the cables.



 Attach the battery wiring to the battery, 

connecting the terminals only on the poles 

marked with the same symbol (red wiring 

“+”, black wiring “-“)! A battery short-circuit 

may cause an explosion!

Run the cables toward the wiring outlet opening 

(on one side of the box, only for Pb-Acid batteries), 

tighten the terminals at the poles and cover them 

with Vaseline.

Insert the battery putting the opening in the box 

(only for the Pb-Acid battery) in a position to run 

the electric wiring to the connector of the machine 

wiring.

After checking that all the controls on the panel 

are in position “0” or at rest, connect the battery 

connector to the machine connector. 



 Close the battery compartment (lowering the 

recovery tank) making sure not to crush any wires.

6.3 MACHINE 

PREPARATION



 Before starting to work, wear non-slip shoes, 

gloves and any other personal protection device 

indicated by the supplier of the detergent used or 

considered necessary based on the operating en-

vironment.

☞

 Do the following before starting to work. Refer 

to the relative sections for a detailed description of 

these steps:

Check the battery charge level and charge, if nec-

essary.