Kruger KFL50BBC, Manual

6.12 

SPECIFIC INSTRUCTIONS FOR THE 

USE OF MODEL  AC 230V

The  AC 230V  model machine may be turned on 

only if the voltage indicated on the tag corresponds 

with the available voltage and that the electrical 

outlet is grounded (earthed).

Do not damage the feed cable; do not crush or 

pull on it.  

Do not run over the feed cable with the machine. 

The cable could wind up in moving parts causing 

a short circuit.

•

ATTENTION !!! - The model AC 230V ma-

chine has parts, which are connected to

the current; contact with these could cause

grave injuries or even death.

- Before executing any type of operation on the

machine always disconnect it from the electrical

source.

- Never touch electric cables that are defective or

worn.

- Before gaining access to the electrical system it is

always necessary to disconnect the machine from

the electrical source.

- In the case of defective, damaged, or cracked

electric cables, replace immediately with authentic

replacement parts.

- The network of connections must be protected

from water spray.

- The patch cord for the connection of the machine

to the mains power must conforms to current sa-

fety rules.

- The electrical system to which the machine is

connected must be equipped with a cutout box.

- It is absolutely forbidden to use the machine in

proximity to swimming pools or stretches of water.

•

EMERGENCY SITUATIONS

In case of emergency:

- Immediately disconnect the machine from

the power mains.

- Immediately apply proper first-aid.

If an accident should occur the machine must not 

be put into operation until a technician authorized 

by the manufacturer has examined it.

6.13 

DRIVING THE MACHINE

Model AC 230V

- Connect the power cable of the machine ( Photo

B - 1) to the power mains using a patch cord.

- Switch ON the general ON-OFF switch ( Photo

A - 1).

- Switch ON the brush motor switch ( Photo A - 2).

•

The brush will start the rotation only when 

the machine operator will operate the brush

operation lever ( Photo B - 4).

- Switch ON the suction motor switch ( Photo A

- 3).

- Lower the squeegee unit by using the lift/lower

lever ( Photo B - 3)

- Lower the brush plate unit by using the lift/lower

lever ( Photo B - 2)

- Wash the floor moving forward slowly, pulling the

brush operation lever ( Photo B - 4); releasing the

lever the brush rotation will stop after few seconds.

•

Remember to lift the squeegee before driving

reverse to avoid damaging it.

Model DC 24V

- Verify that the battery connector placed in the

back of the machine ( Photo D - 7) is connected.

- Put the ignition key ( Photo D - 1) in and turn ON

the machine.

- In the control panel, check the battery charge

status  ( Photo C - 3 )

- Switch ON the brush motor switch ( Photo C - 1).

( ! ) The brush will start the rotation only when the

machine operator will operate the brush operation

lever ( Photo D - 2).

- Switch ON the suction motor switch ( Photo C

- 2).

- Lower the squeegee unit by using the lift/lower

lever ( Photo D - 4)

- Lower the brush plate unit by using the lift/lower

lever ( Photo D - 3)

- Wash the floor moving forward slowly, pulling the

brush operation lever ( Photo D - 2); releasing the

lever the brush rotation will stop after few seconds.

•

Remember to lift the squeegee before driving

reverse to avoid damaging it.

Model DC 24V with traction

- Verify that the battery connector placed in the

back of the machine ( Photo F - 8) is connected.

- Put the ignition key ( Photo F - 1) in and turn ON

the machine.

- In the control panel, check the battery charge

status  ( Photo E - 1 ) and, if sufficient, select the

running speed wished ( Photo E - 3, E - 4 ).

- Switch ON the brush motor switch ( Photo E - 5).

•

The brush will start the rotation only when 

the machine operator will operate the brush

operation lever ( Photo F - 2).

- Switch ON the suction motor switch ( Photo E

- 6).

- Lower the squeegee unit by using the lift/lower

lever ( Photo F - 4)

- Lower the brush plate unit by using the lift/lower

lever ( Photo F - 3)

- Wash the floor moving forward by pulling the

traction lever ( Photo F - 2) up or push the traction

lever down to reverse traction; releasing the lever

the traction will stop immediately and brush rota-

tion will stop after few seconds.

•

Remember to lift the squeegee before driving

reverse to avoid damaging it.

www.kruger.es

Página 35 de 42

Manual KFL50E-KFL50BBC-KFL50BBCTR