background image

9 Related Documents

43 of 50

8417.8/20-EN

9.3 Flange dimensions

Fig. 25: 

Pipe flange dimensions

Ø2a :

Maximum permissible inside diameter of the pipe flange

Ø2b :

Outside diameter

Ø3 :

Minimum inside diameter of the pipe flange

Ø6 :

Minimum outside diameter of the raised face

If the butterfly valve is used for downstream dismantling, the tightening torque must
be lower than:
C1 max. (mdaN) for valve body type 2
C2 max. (mdaN) for valve body type 4

Table 19: 

Pipe flange dimensions [mm]

DN

NPS

Ø2a

Ø2b

Ø3

Ø6

C1

C2

20

¾

32

27

-

46

0.4

5

25

1

37

34

15

55

0.4

5

32

1 ¼

46

43

31

67

0.8

5

40

1 ½

54

49

32

77

1

5

50

2

63

61

33

86

1.3

5

65

2 ½

80

77

55

107

1.6

5

80

3

93

89

71

121

2.7

5

100

4

116

115

90

141

3

5

125

8

141.5

140

119

171

3.2

5

150

6

170.5

7)

169

144

196

4.7

10

200

8

222

7)

220

196

250

6

10

250

10

276.5

7)

273

249

306

8.1

10

300

12

327.5

7)

324

297

358

10

10

350

14

361

356

326

399

-

10

400

16

412

407

370

452

-

16

450

18

463

457

422

505

-

24

500

20

515

508

470

558

-

-

600

24

617

610

566

664

-

-

7

Make sure that the body is centred properly between the flange bolts.

Summary of Contents for BOAX-B



















































Reviews: