Ceiling mounted
Wall mounted
300mm
84mm
Drg No. KSRSF337-IS-B
KSR Lighting Ltd, Unit E Hazleton Interchange, Lakesmere Road, Horndean, Hampshire, PO8 9JU
08.11.2022-PJL
Installation Sheet
KSRSF337
Read these instructions before commencing installation. Please give these instructions to the owner/occupier after
installation to retain for future reference/maintainence.
Navara SF Select
Available Rims: Various please visit www.ksrlighting.com for options
Multi Wattage Triple CCT Bulkhead
IP54 IK10
240V~50Hz 10W/14W/20W
These fittings are Class II and do not need an Earth, but Earth provision is provided.
Important Information
It is recommended that these luminaires are installed and fitted by a qualified electrician ensuring the installation
complies with current IEE wiring regulations & local building control. These products are designed for connection to
a 240V~50Hz supply.
Any faulty, broken or damaged luminaires should be replaced immediately.
KSR will not accept responsibility for any claims arising from a poor installation.
Please Note: The limited warranty shall be deemed null and void in the following circumstances: Failure by the
installer, end user or any third party to exercise caution to protect any covered product or part from outside damage,
adverse temperature (normal operating ambient temperature 0
°C - +30°C), humidity conditions, fluctuations in the
electrical system or physical abuse as well as failure related to workmanship in the installation of the products or
parts.
Important User Advice
Always switch off mains supply before servicing.
Do not use Megger or similar high voltage instruments. Due to the fact this luminaire contains electronic
components that maybe damaged by high test voltages, they must be disconnected from the circuit before testing.
To prevent damage to the driver, do not mix with conventional magnetic ballasts on the same electrical circuit.
At the end of life the luminaire is classed as WEEE under directive 2014/30/EU and should be disposed of in
accordance with local legislation.
Installation Procedure
Isolate mains supply before installation.
Unscrew and retain the four screws and remove the diffuser.
Loosen the single LED tray screw as indicated in Fig.2 and lift the hinged tray to gain access to the wiring terminals.
Pass intended supply wires through grommet.
Ensure the fixing surface is flat and even.
Fix base to the wall, ceiling or besa box using adequate fixings with regard to the type of surface.
Ensure incoming cables are protected.
Terminate wiring as per Fig. 3, please note an Earth terminal is only supplied to aid the continuation of the Earth
circuit.
Please ensure battery is connected, this battery compartment can be accessed as shown overleaf.
Select LED colour and wattage required using the switches on the LED driver Note: Never change the LED colour
or wattage with the luminaire powered on as this can damage the luminaire. Fig. 4.
To set Photocell adjust the Lux level required via the adjuster (anti-clockwise = lowest, clockwise = highest)
and to test simply cover photocell when powered on in daylight and wait for the luminaire to Light up.
Proceed to Re-secure the LED tray.
Make sure the seal is in place in the diffuser and undamaged.
Replace the diffuser re-secure using the four retained screws.
Turn on the mains supply and test luminaire. If using an optional rim clip the rim over the fitting.
This fitting requires a 24 Hour initial charge period prior to any emergency testing, please see
overleaf for testing routine, write on the battery label in permanent ink the date of commissioning.
All results must be recorded and left with the end user.
The battery has a design life of at least 4 years but should be replaced if the duration of
operation is less than 3 hours after a 24hr charge time with no interrupted supply.
Fig. 1
Fig. 2
Gear Tray Retaining Screw
3000K
4000K
6000K
20W
14W
10W
Model: KSRSF330/331/332/333
KSRSF400/401/402/403
Input:220~240Vac 50/60Hz
Output:80-120VDC 175mA(Max)
Prated:20W Max
Tc
Ta:40
°C TC:85°C
V+
G-
W-
E+
Made in China
G-
G+
N
L
Fig. 4
Wattage
LED Colour
Fig. 3
Mains Supply
Luminaire
L- Brown
Permanent Live - Black
N - Blue
Neutral - Blue
L
N
L- Brown
Switch Live - Brown
'L
KSR Lighting Aftersales: 023 92 674343
E-mail: aftersales@ksrlighting.com
Lamp Details
Lamp: LED
Wattage: 10W, 14W, 20W
Colour: 3000K, 4000K and 6000K CCT
CRI: Ra>84
This product contains a light source of energy efficiency class F
Lumen output
CCT
10W
14W
20W
3000K
4000K
1145lm
1261lm
1658lm
1457lm
2126lm
1819lm
6000K
1212lm
1559lm
1947lm
PLEASE NOTE: If using an optional rim to ensure the photocell is
not obscured from ambient light. Measure 18mm from the back
of the rim and slowly drill a 10mm hole using a brad point drill bit.
Install rim to line up the hole with the sensor.
Turn on the mains supply and test luminaire.
Instruction when using Photocell with Optional Rim
