background image

Ceiling mounted

Wall mounted

300mm

84mm

Drg No. KSRSF337-IS-B

KSR Lighting Ltd, Unit E Hazleton Interchange, Lakesmere Road, Horndean, Hampshire, PO8 9JU

08.11.2022-PJL

Installation Sheet

KSRSF337

Read these instructions before commencing installation. Please give these instructions to the owner/occupier after

installation to retain for future reference/maintainence.

Navara SF Select

 Available Rims: Various please visit www.ksrlighting.com for options

Multi Wattage Triple CCT Bulkhead

IP54  IK10

240V~50Hz 10W/14W/20W

These fittings are Class II and do not need an Earth, but Earth provision is provided.

Important Information

It is recommended that these luminaires are installed and fitted by a qualified electrician ensuring the installation

complies with current IEE wiring regulations & local building control. These products are designed for connection to

a 240V~50Hz supply.

Any faulty, broken or damaged luminaires should be replaced immediately.

KSR will not accept responsibility for any claims arising from a poor installation.

Please Note: The limited warranty shall be deemed null and void in the following circumstances: Failure by the

installer, end user or any third party to exercise caution to protect any covered product or part from outside damage,

adverse temperature (normal operating ambient temperature 0

°C - +30°C), humidity conditions, fluctuations in the

electrical system or physical abuse as well as failure related to workmanship in the installation of the products or

parts.

Important User Advice

Always switch off mains supply before servicing.

Do not use Megger or similar high voltage instruments. Due to the fact this luminaire contains electronic

components that maybe damaged by high test voltages, they must be disconnected from the circuit before testing.

To prevent damage to the driver, do not mix with conventional magnetic ballasts on the same electrical circuit.

At the end of life the luminaire is classed as WEEE under directive 2014/30/EU and should be disposed of in

accordance with local legislation.

Installation Procedure

Isolate mains supply before installation.

Unscrew and retain the four screws and remove the diffuser.

Loosen the single LED tray screw as indicated in Fig.2 and lift the hinged tray to gain access to the wiring terminals.

Pass intended supply wires through grommet.

Ensure the fixing surface is flat and even.

Fix base to the wall, ceiling or besa box using adequate fixings with regard to the type of surface.

Ensure incoming cables are protected.

Terminate wiring as per Fig. 3, please note an Earth terminal is only supplied to aid the continuation of the Earth

circuit.

Please ensure battery is connected, this battery compartment can be accessed as shown overleaf.

Select LED colour and wattage required using the switches on the LED driver Note: Never change the LED colour

or wattage with the luminaire powered on as this can damage the luminaire. Fig. 4.

To set Photocell adjust the Lux level required via the adjuster (anti-clockwise = lowest, clockwise = highest)

and to test simply cover photocell when powered on in daylight and wait for the luminaire to Light up.

Proceed to Re-secure the LED tray.

Make sure the seal is in place in the diffuser and undamaged.

Replace the diffuser re-secure using the four retained screws.

Turn on the mains supply and test luminaire. If using an optional rim clip the rim over the fitting.

This fitting requires a 24 Hour initial charge period prior to any emergency testing, please see

overleaf for testing routine, write on the battery label in permanent ink the date of commissioning.

All results must be recorded and left with the end user.

The battery has a design life of at least 4 years but should be replaced if the duration of

operation is less than 3 hours after a 24hr charge time with no interrupted supply.

Fig. 1

Fig. 2

Gear Tray Retaining Screw

3000K
4000K
6000K

20W
14W
10W

Model: KSRSF330/331/332/333

  KSRSF400/401/402/403

Input:220~240Vac 50/60Hz

Output:80-120VDC 175mA(Max)

Prated:20W Max

Tc

Ta:40

°C TC:85°C

V+

G-

W-

E+

Made in China

G-

G+

N

L

Fig. 4

Wattage

LED Colour

Fig. 3

Mains Supply

Luminaire

L- Brown

Permanent Live - Black

N - Blue

Neutral - Blue

L

N

L- Brown

Switch Live - Brown

'L

KSR Lighting Aftersales: 023 92 674343

E-mail: aftersales@ksrlighting.com

Lamp Details

Lamp: LED

Wattage: 10W, 14W, 20W

Colour: 3000K, 4000K and 6000K CCT

CRI: Ra>84

This product contains a light source of energy efficiency class F

Lumen output

CCT

10W
14W

20W

3000K

4000K

1145lm

1261lm
1658lm

1457lm

2126lm

1819lm

6000K

1212lm
1559lm
1947lm

PLEASE NOTE: If using an optional rim to ensure the photocell is

not obscured from ambient light. Measure 18mm from the back

of the rim and slowly drill a 10mm hole using a brad point drill bit.

Install rim to line up the hole with the sensor.

Turn on the mains supply and test luminaire.

Instruction when using Photocell with Optional Rim

Reviews: