background image

 

71 

Current THDi 

≤3%(100% nonlinear load)   

Bypass Voltage 

Range   

Max.voltage: 220V:+25 %( op10%, +15%, +20%); 

230V:+20 %( op10%, +15%);     
240V:+15 %( op10%); 

Min. voltage:-45 %( optional -10%, -20%,-30%) 
Frequency protection range: ±10% 

Output

 

Phase   

3 Phase 4 Wires and Ground 

Rated Voltage 

380/400/415Vac   

Power Factor 

Voltage Regulation 

±1% 

Frequency 

Utility 

Mode 

±1%/±2%/±4%/±5%/±10%of the rated frequency(optional)

Battery 

Mode 

(50/60±0.1)Hz 

Crest Factor 

3:1 

THD 

≤2% with linear load   

≤4% with non linear load   

Overload 

Inverter overload capability: 

  105% < load ≤ 110%: transfer to bypass mode after 60 

min 

  110% < load ≤ 125%: transfer to bypass mode after 60 

min 

  125% < load ≤ 150%: transfer to bypass mode after 60 

min 
Bypass overload capability: 

  Temperature ≤ 30°C, load ≤ 135%: run for a long time 

  Temperature ≤ 40°C, load ≤ 125%: run for a long time 

  1000% load: run for 100 ms 

Battery

 

Voltage 

Optional Voltage: 
±180V/192V/±204V/±216V/±228V/±240/±252/±264/±276/±
288/±300Vdc(30/32/34/36/38/40/42/44/46/48/50pcs 
optional) 
360Vdc~600Vdc (30~50 pcs, 36 pcs define, 36 ~ 50 pcs 
no power derating; 32~34 pcs output power factor 0.9;30 
pcs output power factor 0.8;) 

charge current (A)

 max.

140A 

180A 

200A 

Transfer Time 

Utility to Battery : 0ms; Utility to bypass: 0ms 

Protection 

Short Circuit 

Hold Whole System 

Overheat 

Line Mode: Switch to Bypass; Backup Mode: Shut down 

UPS immediately 

Battery Low 

Alarm and Switch off 

Self-diagnostics 

Upon Power On and Software Control   

EPO 

Shut down UPS immediately 

Battery   

Advanced Battery Management   

Noise Suppression 

Complies with EN62040-2 

Communication Interface

 

CAN, RS232, RS485, LBS, Parallel, Relay card, SNMP 

card(optional) 

Environment 

Operating 

Temperature 

0

℃~

40

 

Storage Temperature

-25

℃~

55

 

Humidity 

0

95% non condensing 

Summary of Contents for HIP3300E















































































Reviews: