KTM 250 1998 Repair Manual Download

Page: 18 / 59

4.0 Servicing on individual components

Chap.

Component / Component unit

Page

4.1

Right housing half . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

4.2

Left housing half . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2

4.3

Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

4.4

Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

4.5

Piston ring end gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

4.6

Measuring cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4

4.7

Exhaust control in cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

4.8

Preassembly of cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

4.9

Nikasil coating of cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6

4.10

Exhaust control in clutch cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6

4.11

Preassembly of clutch cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6

4.12

Reed valve, intake flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-6

4.13

Kickstarter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7

4.14

Preassembly of kickstarter shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7

4.15

Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8

4.15.1 Assembly of main shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8
4.15.2

Assembly of countershaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8

4.16

Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9

4.17

Replacing outer clutch hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9

4.18

Shift mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10

4.19

Preassembly of shift shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-10

4.20

Ignition (Kokusan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11

4.20.1

Spark plug (NGK BR 8 ECM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11

4.20.2

Check stator and pulse generator (Kokusan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-11

4.21

Ignition (SEM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12

4.21.1

Spark plug (NGK BR 8 ECM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12

4.21.2

Check stator (SEM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-12

Engine housing

OTE

: R

EAD THROUGH THE FOLLOWING SECTION BEFORE COMMENCING WORK

. T

HEN DETERMINE THE ASSEMBLY SEQUENCE SO THAT THE ENGINE

HOUSING HALVES ONLY NEED TO BE HEATED UP ONCE BEFORE REPLACING THE BEARINGS

AVING FIRST REMOVED THE DOWELS

IN ORDER TO EXPEL THE BEARINGS OR REMOVE THEM WITH LIGHT MALLET BLOWS

THE HOUSING HALVES MUST

BE PLACED ON A SUITABLY LARGE PLANE SURFACE

SUPPORTING THE WHOLE OF THE SEALING SURFACE WITHOUT DAMAGING IT

. A

WOODEN PANEL IS

BEST USED AS A BASE

EARINGS OR SHAFT SEAL RINGS SHOULD NOT BE HAMMERED INTO THEIR SEATS

. I

F NO SUITABLE PRESS IS AVAILABLE

USE A SUITABLE MANDREL AND

HAMMER THEM IN WITH GREAT CARE

. C

OLD BEARINGS WILL PRACTICALLY DROP INTO THEIR SEATS AT AN ENGINE HOUSING TEMPERATURE OF APPROX

150° C.

FTER COOLING

SHOULD THE BEARINGS FAIL TO LOCK IN THE BORE

THEY ARE BOUND TO ROTATE AFTER WARMING

. I

N THAT EVENT THE HOUSING

MUST BE REPLACED

Summary of Contents for 250 1998




























































Search results

Summary of Contents for 250 1998

Reviews:

Related manuals for 250 1998

Brands by name

Popular brands

KTM 250 1998, Repair Manual

Search results

Summary of Contents for 250 1998

Reviews:

Related manuals for 250 1998

Brands by name

Popular brands