KTM F7103Q3 Setup Instructions Download

Page: 32 / 37

TECHNICAL DATA

4.1

chassis tightening torques

Screw, fixed grip

5 Nm (3.7 lbf ft)

Loctite

243™

Spoke nipple, front wheel

M4.5

6 Nm (4.4 lbf ft)

–

Spoke nipple, rear wheel

M4.5

6 Nm (4.4 lbf ft)

–

Remaining nuts, chassis

5 Nm (3.7 lbf ft)

–

Remaining screws, chassis

5 Nm (3.7 lbf ft)

–

Screw, battery terminal (All 250/300
models, XC

‑

W US, XC

‑

W Six Days US)

2.5 Nm (1.84 lbf ft)

–

Screw, light switch (all
EXC/EXC Six Days models, 125 XC

‑

1 Nm (0.7 lbf ft)

–

Screw, shock absorber adjusting ring

5 Nm (3.7 lbf ft)

–

Nut, cable on starter motor (All
250/300 models, XC

‑

W US,

‑

W Six Days US)

4 Nm (3 lbf ft)

–

Remaining nuts, chassis

10 Nm (7.4 lbf ft)

–

Remaining screws, chassis

10 Nm (7.4 lbf ft)

–

Screw, ball joint of push rod on foot
brake cylinder

10 Nm (7.4 lbf ft)

Loctite

243™

Screw, chain sliding guard

6 Nm (4.4 lbf ft)

Loctite

243™

Screw, front brake disc

14 Nm (10.3 lbf ft)

Loctite

243™

Screw, rear brake disc

14 Nm (10.3 lbf ft)

Loctite

243™

Screw, throttle grip

5 Nm (3.7 lbf ft)

–

Nut, foot brake lever stop

20 Nm (14.8 lbf ft)

–

Nut, rear sprocket screw

35 Nm (25.8 lbf ft)

Loctite

2701™

Nut, rim lock

12 Nm (8.9 lbf ft)

–

Remaining nuts, chassis

25 Nm (18.4 lbf ft)

–

Remaining screws, chassis

25 Nm (18.4 lbf ft)

–

Screw, bottom triple clamp (All stan-
dard EXC/XC-W models)

15 Nm (11.1 lbf ft)

–

Screw, bottom triple clamp (All
Six Days models)

15 Nm (11.1 lbf ft)

–

Screw, chain sliding piece

15 Nm (11.1 lbf ft)

–

Screw, engine brace

25 Nm (18.4 lbf ft)

Loctite

2701™

Screw, fork stub

15 Nm (11.1 lbf ft)

–

Screw, front brake caliper

25 Nm (18.4 lbf ft)

Loctite

243™

Screw, handlebar clamp

20 Nm (14.8 lbf ft)

–

Screw, side stand attachment

35 Nm (25.8 lbf ft)

Loctite

2701™

Screw, subframe

35 Nm (25.8 lbf ft)

Loctite

2701™

Screw, top steering stem (All stan-
dard EXC/XC-W models)

20 Nm (14.8 lbf ft)

–

Screw, top steering stem (All Six Days
models)

17 Nm (12.5 lbf ft)

Loctite

243™

Screw, top triple clamp (All
standard EXC/XC-W models)

20 Nm (14.8 lbf ft)

–

Screw, top triple clamp (All Six Days
models)

17 Nm (12.5 lbf ft)

–

Engine bracket screw

M10

60 Nm (44.3 lbf ft)

–

Remaining nuts, chassis

M10

45 Nm (33.2 lbf ft)

–

Remaining screws, chassis

M10

45 Nm (33.2 lbf ft)

–

Screw, handlebar support

M10

40 Nm (29.5 lbf ft)

Loctite

243™

Screw, bottom shock absorber

M12

80 Nm (59 lbf ft)

Loctite

2701™

Screw, top shock absorber

M12

80 Nm (59 lbf ft)

Loctite

2701™

Nut, seat fixing

M12x1

20 Nm (14.8 lbf ft)

–

Nut, swingarm pivot

M16x1.5

100 Nm (73.8 lbf ft)

–

Summary of Contents for F7103Q3






































Search results

Summary of Contents for F7103Q3

Reviews:

Related manuals for F7103Q3

Brands by name

Popular brands

KTM F7103Q3, Setup Instructions

Search results

Summary of Contents for F7103Q3

Reviews:

Related manuals for F7103Q3

Brands by name

Popular brands