background image

3

WORK

14

3.15

Opening the filler cap

Danger

Fire hazard

Fuel is highly flammable.

Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with
the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with
soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that has been contaminated with
fuel. Store fuel properly in a suitable canister and keep away from children.

Warning

Environmental hazard

Improper handling of fuel is a danger to the environment.

Do not allow fuel to get into the ground water, the ground, or the sewage system.

M00799-10

Lift cover

of the filler cap and insert ignition key

in the fuel tank lock.

M00801-10

Note

Danger of damage

Ignition key breakage.

To take pressure off of the ignition key, push down on the filler cap. Damaged
ignition keys must be replaced.

Turn ignition key

clockwise.

Fold open filler cap

.

3.16

Closing the filler cap

M00802-10

Fold down filler cap

.

Turn ignition key

clockwise.

M00800-10

Push down the filler cap and turn the ignition key

counterclockwise until the

tank lock closes.

Warning

Fire hazard

Fuel is highly flammable, poisonous and harmful to your

health.

After closing the filler cap, ensure that it is locked properly. Change
clothing that has been contaminated with fuel. Immediately clean con-
taminated areas on the skin with soap and water.

Summary of Contents for Super Adventure 2016


























Reviews: