background image

PRINTED IN THE USA © KUBOTA TRACTOR CORPORATION 2022                                                Code: 77700

-

12811 (Rev. A)

 

CARE AND MAINTENANCE 

 

 

(IMPORTANT: Be sure to leave this page with the owner once installation is complete)

 

 

Check and tighten hardware after 20 hours of operation.  

 

Periodically inspect and tighten hardware for the remainder of the unit

s service life.

 

 

 

 

Keep the enclosure components clean in order to prevent dust and dirt from forming an unattractive 

film.  The life of your windows, doors, and roof panels depends upon following these care proce-

dures:

 

 

WINDSHIELD:

 

 

1)

 

NEVER USE

 AN ALCOHOL

-

BASED PRODUCT FOR CLEANING PLASTIC WINDOWS. Many 

brand

-

name glass cleaners contain alcohol that will result in deterioration of the windows.

 

2)

 

Wash with a mild soap or detergent using your bare hands to free or dislodge any caked

-

on dirt 

or other foreign particles.

 

3)

 

A soft, grit

-

free cloth, sponge, or chamois may be used but only as a means of carrying water to 

the windows.

 

4)

 

The interior should be lightly dusted (NOT WIPED) with a clean soft cloth or chamois.  The cloth 

or chamois should be kept free of grit by frequent rinsing in clean water.

 

5)

 

Grease and oil may be removed with kerosene.

 

 

DOORS AND REAR PANELS:

 

 

1)   

NEVER USE 

AN ABRASIVE DETERGENT/VEHICLE CLEANER OR A WIRE BRISTLED 

BRUSH.  Do not use any  

CITRUS BASED CLEANERS 

such as orange or lemon.  Use of these 

products will cause the plastic to become permanently damaged.

 

2)   Clean the enclosure surfaces thoroughly with warm soapy water and a COTTON cloth or cham-

ois.  Be sure to use mild soap, specifically a dish liquid or equivalent.  Clean in a light circular 

motion for best results.

 

This manual is the property of the owner. 

 

Be sure to leave with the owner when installation is complete.

 

IMPORTANT CLEANING INFORMATION

 

Summary of Contents for 77700-12652












Reviews: