background image

Section 4: Maintenance & Lubrication 

Table of Contents

6/21/19

AP-PFL4548, AP-PFL5548, & AP-PFL5560 Plate Mounted Pallet Forks 319-038MK

16

Maintenance

DANGER

!

To avoid serious injury or death:  

Always secure equipment with solid, non-concrete supports 
before working under it. Never go under equipment supported 
by concrete blocks or hydraulics. Concrete can break, 
hydraulic lines can burst, and/or hydraulic controls can be 
actuated even when power to hydraulics is off.

WARNING

!

To avoid serious injury or death:  

Perform scheduled maintenance. Check for loose 

hardware, missing parts, broken parts, structural cracks, 
and excessive wear. Make repairs before putting implement 
back into service.

Backup alarm must be in good working order to warn 

others. Use a backup camera or rear-view mirror that is in 
good condition to help see undesirable situations behind the 
unit. Drive at a slower speed to compensate for blind spots.

Do not alter implement or replace parts on the implement 

with other brands. Other brands may not fit properly or 
meet OEM (Original Equipment Manufacturer) 
specifications. They can weaken the integrity and impair the 
safety, function, performance, and life of the implement. 
Replace parts only with genuine OEM parts.

Proper servicing and adjustments are key to the long life 
of any implement. With careful inspection and routine 
maintenance, you can avoid costly downtime and repair.

1.

After using your pallet fork for a few lifts, check forks 
to make sure they are still secured and check pallet 
fork to make sure it is still properly attached to the 
loader hitch.

2.

Check forks to make sure they are not damaged, 
broken, or worn excessively. Repair or replace as 
needed.

3.

Always remove any material that has become 
entangled in the forks before continuing to use them.

4.

Replace any worn, damaged, or illegible safety 
labels by obtaining new labels from your Land Pride 
dealer.

Section 4: Maintenance & Lubrication

Long-Term Storage

Clean, inspect, service, and make necessary repairs to 
the attachment when storing it for long periods and at the 
end of the season. This will help ensure the unit is ready 
for field use the next time you hook-up to it.

1.

Remove any dirt and grease that may have 
accumulated on the pallet fork. Scrape off compacted 
dirt and then wash its surface thoroughly with a 
garden hose.

2.

Inspect pallet fork for loose, damaged, or worn parts 
and adjust or replace when needed.

3.

Repaint parts where paint is worn or scratched to 
prevent rust. Ask your Kubota dealer for touch-up 
paint. Paint is available in aerosol can, quarts, and 
gallon sizes. See chart below.

4.

Replace all damaged or missing decals.

5.

A coating of oil may also be applied to areas where 
paint is worn off to minimize oxidation.

6.

Store pallet fork inside a building and away from 
human activity if possible. Inside storage will reduce 
maintenance and make for a longer life. 

7.

Follow all unhooking instructions on page 15 when 
disconnecting skid steer or tractor from the Plate 
Mounted Pallet Fork.

8.

Do not allow children to play on or around the stored 
pallet fork.

Kubota Touch-up  Paint

Part No.

Part Description

77700-06430 GLOSS BLACK ENAMEL SPRAY CAN
77700-06431 GLOSS BLACK ENAMEL QUART
700 00-00017 GLOSS BLACK ENAMEL GALLON

Summary of Contents for AP-PFL4548





























Reviews: