65
PERIODIC SERVICE
ENGLISH
3. After all coolant is drained, install the drain plugs.
4. Fill with clean water and cooling system cleaner.
5. Follow directions of the cleaner instruction.
6. After flushing, fill with clean water and anti-freeze until
the coolant level is just below the fill port on the
radiator.
Install the radiator cap securely.
7. Fill with coolant up to the "FULL" mark on the recovery
tank.
8. Start and operate the engine for a few minutes.
9. Stop the engine and let cool.
10.Check coolant level of recovery tank and add coolant
if necessary.
A
Do not start engine without coolant.
A
Use clean, distilled water and anti-freeze to fill the
radiator and recovery tank.
A
When the anti-freeze is mixed with water, the anti-
freeze mixing ratio must be less than 50%.
A
Securely tighten radiator cap. If the cap is loose or
improperly fitted, water may leak out and the engine
could overheat.
B
Anti-freeze
To avoid personal injury:
A
When using anti-freeze, put on some protection
such as rubber gloves (Anti-freeze contains
poison.).
A
If anti-freeze is ingested, induce vomiting at
once and seek medical attention.
A
When anti-freeze comes in contact with the
skin or clothing, wash it off immediately.
A
Do not mix different types of Anti-freeze. The
mixture can produce chemical reaction
causing harmful substances.
A
Anti-freeze is extremely flammable and
explosive under certain conditions. Keep fire
and children away from anti-freeze.
A
When draining fluids from the engine, place
some container underneath the engine body.
A
Do not pour waste onto the grounds, down a
drain, or into any water source.
A
Also, observe the relevant environmental
protection regulations when disposing of anti-
freeze.
If it freezes, coolant can damage the cylinders and
radiator. If the ambient temperature falls below 0
(32
) or before a long-term storage, let out cooling water
completely, or mix fresh water with long-life coolant and fill
the radiator and reserve tank with the mixture.
1. Long-life coolant (hereafter LLC) comes in several
types. Use ethylene glycol (EG) type for this engine.
2. Before employing LLC-mixed cooling water, fill the
radiator with fresh water and empty it again. Repeat
this procedure 2 or 3 times to clean up the inside.
3. Mixing the LLC
Put the LLC in cooling water in the percentage (%) for
a target temperature. When mixing, stir it up well, and
then fill into the radiator.
4. The procedure for the mixing of water and anti-freeze
differs according to the make of the anti-freeze and the
ambient temperature. Refer to SAE J1034 standard,
more specifically also to SAE J814c.
A
When the anti-freeze is mixed with water, the anti-
freeze mixing ratio must be less than 50%.
(1) Engine drain plug
(1) Clamp
(2) Recovery tank
(3) Recovery tank cap
(A) "FULL"
(B) "LOW"
Vol %
Anti-freeze
Freezing Point
Boiling Point *
(
)
(
)
40
50
-24 (-12)
-37 (-34)
106 (222)
108 (226)
Summary of Contents for GR1600-II
