G-31
MX5100, WSM
G GENERAL
[6] CHECK POINTS OF EVERY 400 HOURS
Replacing Hydraulic Oil Filter Cartridge and Changing
Transmission Fluid
CAUTION
• Be sure to stop the engine before replacing the oil filter
cartridge.
• Allow engine to cool down sufficiently, oil can be hot and
can burn.
1. Remove the drain plugs at the bottom of the transmission case
and drain the oil completely into the oil pan.
2. After draining reinstall the drain plugs.
3. Remove the oil filter cartridge.
4. Wipe off metal fillings from the magnetic filter with a clean rag.
5. Put a film of clean transmission oil on the rubber seal of the new
filter cartridge.
6. Quickly tighten the filter until it contacts the mounting surface,
then tighten it by hand an additional 1/2 turn only.
7. After the new filter has been replaced, fill with oil up to the upper
line of the gauge.
8. After running the engine for a few minutes, stop the engine and
check the oil level again, add oil to the prescribed level
9. Make sure that the transmission fluid does not leak past the seal
on the filter
IMPORTANT
■
• To prevent serious damage to the hydraulic system. Use
only a KUBOTA genuine filter.
• Do not operate the tractor immediately after changing the
transmission fluid.
Run the engine at medium speed for a few minutes to
prevent damage to the transmission.
W10870020
Changing Front Axle Case Oil [4WD]
1. To drain the used oil, remove the right and left drain plugs and
filling plug at the front axle case and drain the oil completely into
the oil pan.
2. After draining reinstall the drain plugs.
3. Remove the oil level check plug.
4. Fill with the new oil up to the check plug port.
5. After filling reinstall the filling plug and check plug.
W10366680
Oil capacity
44.0 L
11.6 U.S.gals
9.7 Imp.gals
(1) Drain Plugs
(2) Hydraulic Oil Filter
(3) Magnetic Filter (Wipe off Metal
Fillings)
(4) Gauge
(5) Oil Inlet
(A) Oil level is acceptable within this
range.
Front axle oil capacity (4WD)
9.0 L
9.5 U.S.qts
7.5 Imp.qts
(1) Check Plug
(2) Filling Plug
(3) Drain Plug
Summary of Contents for MX5100
