background image

     INST

ALLA

TION & OWNER’S MANUAL 

 p.  1 of 15 

The contents of this envelope are the property of the owner. 
Be sure to leave with the owner when installation is complete. 

V5008 

Kubota RTV 

72” Snow Blade

 

  

 

D

o not attempt to install or operate this 

plow until you read and understand all 
warnings and instructions in this manual or 
on the plow. Failure to read all warnings 
and instructions could lead to serious injury 
or death.   

 

 

  Curtis Cabs, blades and general accessories

  exceed the vehicle's rated capacity including

  from the vehicle's rated capacity and never

  brochures. Deduct the accessory's total weight

  Curtis accessory weights are listed in product

  add additional weight to the base vehicle. All

  driver and passenger.

ADDED

WEIGHT

These instructions are only valid for attachment to RTV-X900, 

RTV-X1100C, RTV-X1120, RTV-XG850, and RTV-X1140 utility vehicles.  

 

Note: Front Heavy Duty Springs (V5218) or Heavy Duty Spring Damper 
Assembly (V5219) are required for RTV-X900, RTV-X1120, and RTV-XG850. 
Heavy duty springs come standard on RTV-X1140 model. 
For RTV-XG850, installation of K7591-97900 grill guard kit is required. 

 
                          Approximate Installation Time: 1-2 hours

 

IMPORTANT: Please read the installation instructions 

thoroughly before beginning.  Installation of any item is 

easier if the vehicle is clean and free of debris. 

manual p/n: 77700-05199 (V5008P1) 
(Rev. D) 11/20/2018 

California Health and Safety Proposition 65 Warning: 

This product may contain 

chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.  

 

Summary of Contents for V5008
















Reviews: