57
PERIODIC SERVICE
ENGLISH
The oil filter cartridge must be changed
every 200 service
hours
.
Always use a genuine oil filter.
1. Drain the engine oil. (See step 1 and 2 in "Changing
Engine Oil" in "EVERY 100 HOURS" in "PERIODIC
SERVICE" section.)
2. Remove the old filter and wipe off the filter adapter with
a clean cloth.
3. Place a new replacement filter in a shallow pan with
the open end up. Pour new oil, of the proper type, in
through the threaded center hole. Stop pouring when
the oil reaches the bottom of the threads. Allow a
minute or 2 for the oil to be absorbed by the filter
material.
4. Apply a thin film of clean oil to the rubber gasket on the
new oil filter.
5. Install the new oil filter to the filter adapter. Hand
tighten the filter clockwise until the rubber gasket
contacts the adapter, then tighten the filter an
additional
2/3 turn
.
6. Fill the engine with the proper oil to the "FULL" or "F"
mark on the dipstick. Always check the oil level with
the dipstick before adding more oil.
7. Reinstall the oil fill cap/dipstick and tighten securely.
8. Start the engine and check for oil leaks. Recheck oil
level before placing the engine into service.
Stop the engine, correct any leaks, and allow a minute
for the oil to drain down, then recheck the level on the
dipstick.
A
To prevent extensive engine wear or damage, always
maintain the proper oil level in the crankcase. Never
operate the engine with the oil level below the "ADD"
or "L" mark or above the "FULL" or "F" mark on the
dipstick.
B
Cleaning Engine Shroud
Consult your local KUBOTA Dealer for this service.
B
Replacing Fuel Filter
(See "Checking Fuel Lines and Fuel Filter" in "EVERY
100 HOURS" in "PERIODIC SERVICE" section.)
EVERY 250 HOURS
B
Replacing Air Cleaner Outer Element
(See "Checking Air Cleaner Outer Element" in "EVERY
100 HOURS" in "PERIODIC SERVICE" section.)
B
Checking Air Cleaner Inner Element
(See "Checking Air Cleaner Outer Element" in "EVERY
100 HOURS" in "PERIODIC SERVICE" section.)
EVERY 500 HOURS AFTER 300 HOURS
B
Replacing Transaxle Oil Filter Cartridge
To avoid serious injury:
A
Park the machine on a firm and level surface.
A
Apply the parking brake.
A
Be sure to stop the engine and remove the key
before changing or checking the oil.
A
Allow transmission case to cool down
sufficiently; oil can be hot and may cause
burns.
1. Clean any loose debris from around the oil drain plug,
oil filter, expansion tank cap, and breather port plug.
2. Place an oil drain pan (8 qt. capacity minimum)
beneath the oil drain plug. Remove the oil drain plug
and washer and allow used oil to drain completely.
A
Remove the expansion tank cap to speed up the
draining process.
3. Remove the oil filter.
A
Always replace the filter when performing any internal
maintenance to the transaxle.
4. Wipe the oil filter mounting surface and apply a film of
new oil to the new oil filter o-ring.
5. Install the new oil filter by hand.
6. After hand tightening, torque the oil filter to 13-15.2 N-
m (9.60-11.2 lbf-ft).
7. Inspect oil drain plug and washer. Replace if
damaged.
8. Reinstall the oil drain plug and washer. Torque to 5.7-
8.4 N-m (4.2-6.1 lbf-ft).
9. Loosen breather port plug by 3 turns.
(1) Engine oil filter cartridge
Summary of Contents for Z723
