background image

7

8. Veneering

• 

Layering technique: 

Apply a thin layer of adhesive paste to the surfaces to be veneered and fire.  

(See below for firing instructions)

•  The HeraCeram materials are then layered and fired according to the HeraCeram user instructions.

• 

Stain technique: 

The restoration must be clean and grease-free. A roughened surface is of advan-

tage.

• Personalize restorations with HeraCeram Stains universal and fire. For more intense chromatic 

results, the procedure can be repeated.

•  Finally, glaze with HeraCeram Glaze universal and fire.

• 

Firing procedure: 

Veneers and inlays are positioned and fired on the smallest possible piece of firing 

wool placed of top firing pins.

•  Crowns are fired on suitable firing pins, fan pins, special firing wires or pins with adapted platinum 

foil or firing wool.

Firing recommendations

The firing temperatures given are intended as guidelines. Deviations are possible due to 

varying furnace performance.

General 

 Firing 

 Programme

Pre-heat  

or start 

 temperature

Pre-dry  

and pre-heat 

time

Heat rate

Final 

 temperature

Holding  

time

Vacuum  

start

Vacuum  

stop

 

°C

min

°C/min

°C

min

°C

°C

Adhesive

600

5

100

860

1

600

860

Stain and 

glaze firing

using Stains / 

Glaze 

 universal

600

6

100

860

0,5 – 1

Please follow our detailed processing instructions for processing of HeraCeramPress and the 

instructions in our safety data sheet.

Safety instructions:

Hypersensitivity to the product or its components cannot be ruled out in individual cases – in a sus-

pected case, please contact the manufacturer with regard to the ingredients. In the case of a suspected 

allergy, an allergy test is recommended before treatment. The data indicated corresponds to the best 

of our knowledge and is based on internal investigations. Do not swallow or consume this product. 

Avoid contact with the eyes. If the product does come into contact with the eyes, rinse them thoroughly 

with plenty of water immediately and consult an ophthalmologist. 
If you wish to contact us with regard to the product, please always indicate the lot designation.
Designation lot 

 : See note on packaging.

Dated: 2018-11

1809_15440_GBA_HeraCeram_Press.indd   7

21.12.18   10:24

Summary of Contents for HeraCeramPress

























Reviews: