Kulzer HiLite power Operating Instructions Manual Download

Page: 31 / 40

Operating instructions

HiLite

power

- 11 -

CAUTION

While working with light reflectors with covered holes heat will accumulate in the unit.

Polymerisation processes will not be reproducible and the unit may switch off owing to excess temperature.
To restart the unit, let it cool down for approx. 30 minutes.

Observe the following information:

Insert only clean light reflectors.

Holes may only be covered to the extent required for positioning the prosthetic restoration.

CAUTION

The filter disc ensures that the material is not exposed to any undesired radiation and reduces the generation of heat.

Observe the following information:

The unit may only be operated with filter disc.

Clean the filter disc within regular intervals.

CAUTION

The filter collects dust and contamination from the laboratory and avoids the output of light from the bottom

of the unit. Moreover the fireproof filter protects the unit if it is heated excessively.

Observe the following information:

The unit may only be operated with the filter being inserted.

Check the filter within regular intervals and exchange it if contaminated.

8.2

Errors and how to eliminate those

DISCONNECT FROM MAINS

Risk of fatal injury!
Unplug the unit before opening it.

ELECTRIC SHOCK

Danger of electric shock when unit is opened!

Error

Unit condition

Cause

Elimination

Unit cannot be

switched on

Unit has not been connected

Connect unit with mains supply

Defective fuse

Check fuse in the cold appliance plug and, if required,

exchange the fuse; if error occurs repeatedly, put unit

out of operation and inform service agent. See also

“

Incorrect mains voltage

”

Defective power cord

Replace power cord

Incorrect mains voltage

Use voltage selector to adjust correct input voltage

Initialization / Self

test

No chip card

Insert chip card

Chip card not readable

Chip card defect or chip card may have been

inserted incorrectly

Wrong chip card

Insert correct chip card

Polymerisation

process is not

started or aborted

Limit switch was activated

Close maintenance flap and / or drawer correctly.

If necessary, repeat polymerisation process

No flash lamp inserted or flash lamp

defect

Insert flash lamp and, if required, start polymeri-

sation process again; if error occurs repeatedly,

exchange flash lamp

Symbol explanation

No light appears

Permanent light

1 LED flash per second

2 LED flashes per second

Alternating flashing LEDs

7.6.3 Filter drawer

Has the filter been inserted?

Clean or replace very dirty filters.

7.6.4 Inside the machine

Has the flash lamp been inserted as far as it will go?

Has the chip card been correctly inserted into the card reader?

Is the filter disc in position and clean?

8 Appliance

8.1

Working with the machine

Connect the machine to the power supply and switch it on.

Make sure that the material is placed in the machine on the supplied object
holder (if possible!) and not with the whole plaster model. The large light
reflector allows this to be done, but it significantly prevents the cooling
capability.

Warming can be reduced with the “

Model tray

” spacer when the 180 second

light polymerisation is used frequently. For this purpose, the model must
be placed on the tray with the feet pointing downwards in order to achieve
better ventilation.

Delivery form:

2 pieces “

Model tray”

REF 66017525

Open the polymerisation drawer and insert the prosthetic material in the light
reflector. Close the drawer. Press the button for the respective polymerisation
cycle. The respective LED ring is lit.
The drawer is locked (not in the 6 second cycle). At the end of the polyme-
risation time an acoustic signal (buzzer) is heard and the drawer is unlocked
again. Remove the prosthetic restoration and exchange the reflector pot if it
is heavily contaminated or clean it.
The fan which started at the beginning of polymerisation continues to run until the interior of the unit has been cooled down
to a large extent.

NOTE

The built-in ventilator must cool the prosthetic material evenly and well to ensure an excellent polymerisation result.

This will only happen if the product is positioned in the centre.

Observe the following information:

Place the prosthetic material in the centre of the light reflector.

Align the polymerisation product with the light source to ensure an excellent polymerisation result. If polymerisation is
advantageous on the model, place the model with the greatest possible angle to the light reflector wall. This keeps the
ventilation holes in the floor free. An angular position is favourable as lateral exposure is better on the facing.

When positioning the product, ensure that it is aligned beneath the edge of the light reflector. Otherwise,
the drawer will not close and the object will touch the window pane in the machine.

Insert the drawer as far as it will go.

Select the required polymerisation time and press the button.

NOTE

The 6 second polymerisation time is used to harden the material. All components of Signum

(exception: Opaque)

can be pre-polymerised using the 6 second polymerisation time if a maximum layer thickness of 2 mm is not exceeded.
Then carry out intermediate polymerisation for 90 seconds and end polymerisation for 180 seconds.

To ensure extended service life of the unit, the interior of the unit should have been cooled down sufficiently before the
unit is switched off. The unit should not be switched off as long as the fan is not in standby-mode. (Fan is not turned
off completely).

Attempting to pull out the drawer may result in blocking of the locking magnet. In such cases the drawer needs to be
re-inserted and the unit must be switched off and on; then the drawer can be opened again.

Model tray