EN
16
shown on the corresponding power
indicator and its decimal dot (4) will
keep light up during 10 seconds.
2
Use the cursor slider (2) to choose a
new cooking level between 0 and 9.
As long as the plate is selected, in
other words, with the decimal (4)
dot light up, its power level can be
modified.
TURNING OFF A PLATE
Using the touch slider key (2) lower
the power to level 0. The hotplate will
switch off.
When a hot plate is switched off an
H will appear in its power indicator
(3), if the glass surface of the related
cooking area is hot and there is a risk
of burns. When the temperature drops,
the indicator (3) switches off (if the hob
is disconnected), or otherwise a “-” will
light up if the hob is still connected.
TURNING ALL PLATES OFF
All plates can be simultaneously
disconnected by using the general on/
off sensor
(1). All plate indicators (3)
will turn off. If the heating zone turned
off is hot, its indicator shows an H..
Pan detector
Make sure that the bottom of
the vessel, covers one or more of
the references ( )on the surface
of the hob; (see fig.7 and table 1).
Induction cooking zones have a built-in
pan detector. This way, the plate will
stop working if there is no pan present
or if the pan is not suitable.
The power indicator (3) will show a
symbol to designate “there is no pan
” if, while the zone is on, no pan is
detected or the pan is not suitable
If a pan is taken off the zone while it
is running, the plate will automatically
stop supplying energy and it will
show the symbol for “there is no pan”.
When a pan is once again placed
on the cooking zone, energy supply
will resume at the same power level
previously selected.
When finished, turn off the
cooking zone by using the touch
controls. Otherwise an undesired
operation could occur if a pan is
accidentally placed on the cooking
zone during the 30 seconds. Avoid
possible accidents!
Block Function
With the Block Function, you can block
the other sensors, except for the on/
off sensor (1), in order to avoid
undesired operations. This function is
useful as a childproof safety.
To activate this function, touch sensor
(6) for at least one second. Once
you have done so, the pilot (7) turns
on indicating that the control panel is
blocked. To deactivate the function,
simply touch sensor (6) again.
If the on/off sensor (1) is used
to turn off the appliance while the
block function is activated, it won’t be
possible to turn the cooktop on again
until it unblocks.
Silencer of the beep
When the hob is on, if one presses the
touch key (11) and the locking touch
key (6) simultaneously for three
seconds, the beep that accompanies
each action will be deactivated. The
time indicator (12) will display “OF”.
This deactivation will not be applied
to all the functions, as for example the
beep for on/off, the ending of the timer
or the locking/unlocking of the touch
keys always remain activated.
To once again activate all the beeps
that accompany each action, again
simultaneously press the touch key
(11) and the locking touch key (6)
for three seconds. The time indicator
(12) will display “On”
Stop&Go Function
This function puts the cooking process
on pause. The timer will also be
paused if it is activated.
Activating the Stop&Go function.
Touch the Stop&Go sensor (8) for
one second. The pilot (9) lights up
and the power indicators will show
the symbol to indicate cooking
has been paused.
Deactivating the Stop&Go function
Touch Stop&Go sensor (8) again.
The pilot (9) turns off and cooking
resumes under the same power and
timer settings that were established
before the pause.
Power Function
This function supplies “extra” power
to the plate, above the nominal value.
Said power depends on the size of the
plate, with the possibility of reaching
the maximum value permitted by the
generator.
1
Slide the finger above the
corresponding cursor slider (2)
until the power indicator (3) shows
“9” and keep the finger pressed for
one second, or touch directly on “
” and keep pressed the finger for
one second.
2
The power level indicator (3) will
show the symbol
, and the plate
will start to supply extra power.
The Power function has a maximum
duration specified in Table 1. After this
time, the power level will automatically
adjust to 9. A beep sounds.
On activating the Power function in
one hotplate, it is possible that the
performance of some of the others
may be affected, reducing its power to
a lower level, in which case this will be
displayed on its indicator (3).
Deactivation of Power Function,
before its working time passes, can
be done either by means of touching
cursor “slider” modifying its power level
or repeating step 3.
