18
ENG
1
150/ 120 mm reduction.
2
Supports for tubecover.
2
Supports hall.
6
Wall plugs (Ø8 x 40).
6
Long bolts (Ø5 x 45).
4
Wall plugs (Ø6 x 30).
4
Long bolts (Ø4 x 30).
2
Washers (Ø6,4 x Ø18).
2
Washers (Ø6,4 x Ø12).
2
Screws (Ø3,9 x 13).
4
Screws M4 x 12.
2
Clips.
Fig. 1 (Page 19)
On installing the kitchen hood make sure
that the Safety Instructions set out on page
14 are complied with.
To obtain optimum performance, the external
duct must not be more than FOUR METRES
LONG, have no more than two 90° angles and
its diameter must be at least Ø120.
1) Trace and drill the points for fitting the wall
plugs onto the wall (P) (Ø8 x 40) and (J) (Ø6 x
30).
2) Attach the Supports (O) to the wall using the
long bolts (Q) (Ø5 x 45) and the support (H)
with the long bolts (I) (Ø4 x 30), as in figure 1.
3) Hang the kitchen hood onto the mounted
supports (O). Straighten the appliance by
tightening the long bolts (L) (M4 x 12).
4) Remove the metal filters. Loosen the screws
(X) to dismount the cover top (W). Trace the
location of the long bolts (S) (Ø5 x 45).
5) Take the kitchen hood off.
6) Drill into the wall and fit the wall plugs (R)
(Ø8 x 40).
7) Hang the kitchen hood; tighten the screws
(M) (M4 x 12) with the washers (A3) (Ø6,4 x
Ø12) and the long bolts (S) (Ø5 x 45) with the
washers (T) (Ø6,4 x Ø18).
8) Mount the cover top again (W). Fit the metal
filters.
9) Mount the tubecovers, attaching the lower
one to the support (H) as per the detail in figure
1. Lift the upper tubecover up to the desired
height and mark its shape on the wall. Remove
the tubecovers.
10) Fit the clips (F) to the support (C).
11) Centre the support (C) around the shape
marked; trace and drill the fixing points for the
wall plugs (E) (Ø6 x 30). Attach the support (C)
with the long bolts (D) (Ø4 x 30).
12) Fit the part (B) if the inner tube (not
supplied) is Ø120.
13) Attach the inner tube with a clamp (not
supplied) to (B) or on to the motor's air outlet
vent as the case may be.
14) Once the inner tube is fitted, fit the lower
tubecover around the extractor fan outlet and
attach the upper tubecover with the screws (G)
(Ø3,9 x 13).
When exterior gas extraction is not possible,
then the kitchen hood may be set to purify the
air by recycling it through active charcoal
filters.
The active charcoal filters have an active life of
between three to six months, depending on
the individual conditions of use. These filters
cannot be washed nor regenerated. They must
be replaced once their useful life comes to an
end.
Fig. 3 (Page 19)
1) Remove the metal filters. Loosen the screws
(J) to dismount the cover top (I).
2) Put the filters into the lateral draught section
of the motor making the holes in the filters
match up (A) with the pivots (B) of the motor
carcass. Turn as indicated in the diagram.
3) Mount the support again (I). Fit the metal
filters.
4) Remove the tubecovers (E). Use the wall
plugs and the previously installed upper
tubecover's support (G) long bolts (D) to fix
diffuser (C) into the wall.
5) Connect the diffuser base (C) to the motor
exit via the inner tube (not supplied). Use
clamps (Not supplied). Fit the tubecovers (E)
again.
Active charcoal filters (Optional)
Installation
Accesories supplied
Manual KDT.qxd 17/06/2004 13:47 Page 18
