background image

16

GB

16

12c

12d

8

Mounting the hood body

• Open the ducting panels.
• Disconnect the panel from the hood canopy by

sliding the fixing pin lever.

(A)

• Remove the metal grease filters by turning the

handles provided.

• Adjust the two screws 

Vr

, on brackets 

11a

, to a

minimum.

(B)

• Hook the hood canopy onto the two brackets

11a.

• From inside the hood canopy, adjust the screws

Vr

 to set the Hood Canopy level.

• Tighten the safety screw 

12a

.

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

To install the Ducting Version of  the hood, the optional Ducting chimney kit must be purchased.

RECIRCULATION VERSION AIR OUTLET

To install the Recirculation Version of the hood, the optional Activated charcoal cartridge kit must
be purchased.

• Screw the filter cover onto the air outlet, using

four screws 

12c

 (2.9 x 12.5).

• Fix the directional grille 

8

 on the recirculation

air outlet using the 2 screws 

12d

 (2,9 x 9,5)

provided.

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole

switch having a contact gap of at least 3 mm.

• Remove the grease filters (see paragraph Maintenance)

being sure that the connector of the feeding cable is
correctly inserted in the socket placed on the side of
the fan

( A )

( B )

Vr

Summary of Contents for KD 9550










Reviews: