background image

19

GB

A

B

Activated charcoal filter (Recirculation version)

REPLACING THE ACTIVATED CHARCOAL FILTER

• The filter is not washable and cannot be

regenerated. It must be replaced when led 

S1

flashes or at least every 4 months. The alarm
signal will only light up when the extractor
motor is switched on.

Alarm signal reset

• Switch off the lights and extractor motor.
• Press button 

T3 

for at least 3 seconds, until the

leds start to flash.

Replacing the Filter

• Remove the metal grease filters
• Remove the saturated activated carbon filters

as shown (

A

).

• Fit the new filters (

B

).

• Replace the metal grease filters.

Alarm signal activation

• In Recirculation version Hoods, the Filter saturation alarm can be enabled on installation or at a

later date. Turn the Lights and the suction Motor off.

• Disconnect the Hood using the Main switch or the double-pole switch on the mains power supply.
• Restore the connection by pressing and holding 

T1

.

• Release the button.  All five LEDs are turned on
• Within 3 seconds press 

T1

 until LEDs  T1 and T4 flash in confirmation:

LED flashes twice - Activated charcoal filter saturation alarm ENABLED
LED flashes once - Activated charcoal filter saturation alarm DISABLED

Lighting

LIGHT REPLACEMENT

20 W halogen light.

• Remove the light cover by unfastening the

screws that hold it.

• Extract the lamp from the Support.
• Replace with another of the same type, making

sure that the two pins are properly inserted in
the lamp holder socket holes.

• Replace the light cover.

Summary of Contents for KD 9550










Reviews: