81
3BA00217 • 2020-10-26 • Rev. 3
Ersa EASY ARM 2
Probleemoplossing
6.1
Standby-werking
De afzuigunit gaat in standby zodra het laatste aangesloten gereedschap in de stand
-
by-modus gaat. Hetzelfde geldt voor de master-slave werking
Er kunnen geen instellingen worden uitgevoerd op de displays van de afzuigunit als deze
in standby staat.
7.
Probleemoplossing
Bericht/gedrag
Oorzaak
Oplossing
De rode LED knippert &
♪
per seconde
De filterbedrijfsduur van 1500 uur
is verstreken.
Vervang het voorfilter en het com
-
bi-filter (hoofdstuk 8) en stel de
bedrijfsduur van het filter opnieuw
in (hoofdstuk 6 en figuur
).
De rode LED brandt continu &
♪
continu gedurende
5 minuten,
schakelt de motor uit.
Afzuigarm verstopt/
filter vol.
Schakel het apparaat uit.
Inspecteer de afzuigarmen op
vreemde voorwerpen en reinig ze
indien nodig; vervang het voorfilter
en het combi-filter (hoofdstuk 8).
Schakel het apparaat in en stel de
bedrijfsduur van het filter opnieuw
in (hoofdstuk 6 en afbeelding
).
De rode LED brandt continu &
♪
lang &
♪
kort
herhalend om de 3 seconden
Spanning te hoog/te laag.
Inspecteer de stroomvoorziening.
De rode LED brandt continu &
♪
lang & 2x
♪
kort
herhalend om de 3 seconden
Motor geblokkeerd/
niet aangesloten/
defect..
Controleer op verstoppingen en
verwijder ze.
Neem contact op met Ersa Service.
De rode LED brandt continu &
♪
lang & 4x
♪
kort
herhalend om de 3 seconden
Systeemparameters corrupt.
Voer een reset uit naar de fa-
brieksinstellingen (hoofdstuk 6 en
figuur
).
Neem contact op met Ersa Service.
De rode LED brandt continu &
♪
lang & 5x
♪
kort
herhalend om de 3 seconden
Kalibratieparameter corrupt.
Neem contact op met Ersa Service.
De rode LED brandt continu &
♪
lang & 6x
♪
kort
herhalend om de 3 seconden
Bedrijfsduur van het filter corrupt
of de gegevens zijn verloren gegaan.
Inspecteer het voorfilter en het
combi-filter, en vervang ze zo nodig
(hoofdstuk 8); en stel de bedrijfs
-
duur van het filter opnieuw in
(hoofdstuk 6 en figuur
).
8.
Onderhoud
Het stof dat bij het solderen ontstaat is schadelijk voor de gezondheid.
Draag daarom bij werkzaamheden aan het open apparaat (bijv. bij het
vervangen van filters) de juiste veiligheidskleding (ten minste een half
-
masker met deeltjesfilter en handschoenen).
Summary of Contents for 0CA10-002
Page 90: ...90 3BA00217 2020 10 26 Rev 3 Ersa EASY ARM 2 3 3 1...
Page 91: ...91 3BA00217 2020 10 26 Rev 3 Ersa EASY ARM 2 8 3 2...
Page 93: ...93 3BA00217 2020 10 26 Rev 3 Ersa EASY ARM 2 5 5 1 EASY ARM 2 5 2 8...
Page 96: ...96 3BA00217 2020 10 26 Rev 3 Ersa EASY ARM 2 8 1 8 2 6 8 3...