background image

3BA00174 • 2014-02-06 • Rev. 5

HR 100   1 / 13

4.  Transport, storage and waste disposal

The device is delivered in a sturdy cardboard box. Please use only the original packaging for 
transportation and intermediate storage. Strictly avoid jerky movements, impacts or putting 
down. The device must be adequately protected against weather influences like rain, fog or 
sea air, etc. For longer storage in high humidity environments the device must be packed up 
air tight, together with a dehumidifying agent. Damage caused by unprofessional transport or 
storage are not covered under warranty.

Notes on waste disposal acc. to the directive 2002/96/EG of the European 
Parliament and the Committee from 27th of January 2003 for for used 
electric and electronic appliances:

Products marked with a crossed out waste bin must not be disposed of 
together with unsorted domestic waste. The municipalities established 
special collecting points for this type of waste. Please consult your council 
and ask for available possibilities for the separated collection of old 
appliances. You thereby contribute to the reuse or other forms of use of old 
appliances, with the aim of protecting the environment and human health.

Summary of Contents for HR 100 A
















































Reviews: