background image

SAFETY................................................................................01

TERMS IN THIS MANUAL...................................................02

INTERNATIONAL ELECTRICAL SYMBOL..........................03

FEATURES & GENERAL SPECIFICATION.........................04

ELECTRICAL SPECIFICATION...........................................06

PRODUCT DESCRIPTION .................................................14

OPERATION.........................................................................15

MAINTENANCE...................................................................27

TEST CERTIFICATE............................................................28

WARRANTY......................................................................... 29

TABLE  OF CONTENTS

TITLE

PAGE NO.

1)

This manual contains information and warnings that must be 
followed for operating the instrument safely and maintaining the
instrument in a safe operating condition. If the instrument is 
used in a manner not specified by the manufacturer, the 
protection provided by the instrument may be impaired. 

Measurement Category  IV 1000V AC  &  DC.

OVERVOLTAGE  CATEGORY  ll  (CAT  II) 

is  for  equipment 

intended to be supplied from the building wiring. It applies both to 

p l u g - c o n n e c t e d   e q u i p m e n t   a n d   t o   P E R M A N E N T LY 

CONNECTED EQUIPMENT.

The  meter   protection   rating,  against   the   users,   is   double 
insulation  per  IEC/EN61010-1  2nd  Ed.,  UL61010-1  2nd  Ed., 
CAN/CSA  C22.2  No.  61010.1-0.92,  IEC/EN61010-2-032, 
UL61010B-2-032,  CAN/CSA  C22.2  No.  61010-2-032-04  & 
IEC/EN61010-031:2002/A1:2008: 

OVERVOLTAGE  CATEGORY  lV  (CAT  IV) 

is  for  equipment 

installed at or near the origin of the electrical supply to a building, 

between  the  building  entrance  and  the  main  distribution  board. 

Such equipment may include electricity tariff meters and primary 

overcurrent protection devices.

Per IEC61010-1 (2010) OVERVOLTAGE CATEGORY

OVERVOLTAGE   CATEGORY   lll  (CAT III)  

is   for   equipment 

intended  to  form  part  of  a  building  wiring  installation.  Such 

equipment  includes  socket  outlets,  fuse  panels,  and  some 

MAINS installation control equipment.

 

- 01 -

Summary of Contents for KM 2777






















Reviews: