background image

®

®

11

12

* Accuracies with film capacitor or better.

** In manual-ranging mode, measurements not specified below 45.0

m

F and 

    450

m

F for 500.0

m

F & 9999

m

F ranges respectively.

CAPACITANCE

m

1            F

10         pF

100       pF

1           nF

10         nF

100       nF

50.00    nF

9999     

m

F**

500.0    

m

F**

50.00    

m

F

5.000    

m

500.0    nF

Range

±(2.5%rdg + 3dgts)

±(1.5%rdg + 3dgts)

±(0.8%rdg + 3dgts)

±(3.5%rdg + 5dgts)

±(5.0%rdg + 5dgts)

Accuracy*

Resolution

CREST MODE FOR V & A FUNCTIONS

Accuracy : 

Specified accuracy ±150 digits 

for changes > 0.8ms in duration.

DC CURRENT

500.0     

m

A

5000      

m

A

50.00    mA

500.0    mA

5.000       A

10.00       A*

0.15mV/

m

A

±(0.2%rdg + 4dgts)

0.15mV/

m

A

3.3mV/mA

3.3mV/mA

45mV/A

45mV/A

0.1     

m

A

1        

m

A

0.01   mA

0.1     mA

0.001    A

0.01      A*

Range

Burden Voltage

Accuracy

Resolution

* 10A continuous, >10A To 20A for 30 seconds max with 5 minutes cool down interval

* 10A continuous, >10A to 20A for 30 seconds max with 5 minutes cool down interval

Range

AC CURRENT

50Hz -- 60Hz

500.0     

m

A

5000      

m

A

50.00    mA

500.0    mA

5.000       A

10.00       A*

0.15mV/

m

A

Burden Voltage

±(0.6%rdg + 3dgts)

40Hz -- 1kHz

500.0    

m

A

5000     

m

A

50.00    mA

500.0    mA

5.000       A

10.00       A*

±(0.8%rdg + 4dgts)

±(1.0%rdg + 4dgts)

±(0.8%rdg + 4dgts)

Accuracy

±(1.0%rdg + 3dgts)

0.15mV/

m

A

0.15mV/

m

A

3.3mV/mA

3.3mV/mA

45mV/A

45mV/A

0.15mV/

m

A

3.3mV/mA

3.3mV/mA

45mV/A

45mV/A

Resolution

0.1     

m

A

1        

m

A

0.01   mA

0.1     mA

0.001    A

0.01      A*

0.1     

m

A

1        

m

A

0.01   mA

0.1     mA

0.001    A

0.01      A*

±(0.6%rdg + 3dgts)

Summary of Contents for KM 5040-T
















Reviews: