background image

•After referring to the operation manual, if assistance is still needed, please consult our web Site at 

www.kushlanproducts.com

• From our web site you may 

e-mail us

 directly If assistance is still required, please call our customer service department 

at  

1-800-469-4178

Safety Alert Symbol: This safety alert symbol is used to 

attract your attention!

• Personal Safety is involved when you see this symbol, Pay extra attention, become alert-be sure to heed it’s message. 

Failure to do so may lead to serious personal injury or damage may occur.
• Warnings and safety instruction: If these warnings and safety instructions are not read and carefully followed, serious 

personal injury could occur.

WARNINGS

1. Do not use, start, or attempt to operate this machine until all of the instructions have been read and fully understood.

2. Never allow anyone to operate this ma-chine unless the person is well acquainted with these rules of safe operation.

3. Never operate this machine without all guards in place and firmly attached to the machine.

4. Make certain that the mixing drum is clear of obstructions and stand clear of the machine with out all guards in place   

    and firmly attached to the machine.

5. When cleaning, lubricating, or adjusting the mixer, disconnect the power plug.

6. Keep all people (except operator) a minimum of five (5) feet away from the machine during operation.

7. Always make certain that the mixer is connected to a properly grounded electric circuit to protect the operator from 

     possible electric shock.

8. Do not plug or unplug the motor while standing in or around damp or wet ground.

9. Do not start the motor if the drum is Fully loaded

10. Do not overload the mixer

11. Never attempt to move the mixer While the motor is on.

SHOULD YOU REQUIRE ANY 

SET-UP OR OPERATING ASSISTANCE WITH YOUR PRODUCT, 

DO NOT RETURN TO ORIGINAL PLACE OF PURCHASE

SAFETY INSTRUCTIONS

 

For the safety of yourself and others around you, it is extremely important that you 

observe the following notes.

1. Keep hands and clothing away from moving parts at all times.
2. Do not operate this machine under the influence of alcohol or while taking medication that impairs the senses or reactions.
3. Make certain that the work area around the machine is clear of debris and obstructions.
4. Keep all unauthorized and untrained people away from the machine at all times.
5. Never let the mixer run unattended even for a brief moment.
6. Turn off the motor when you leave the machine.
7. Only use or operate the mixer on level ground to prevent the mixer from tipping over.
8. Do not abuse the power cord; i.e. Never yank on the cord to disconnect it. Keep the cord away from heat, oil, and sharp edges.
9. Do not overreach while working with the mixer. Keep proper Footing and balance at all times when loading or unloading the  

    mixer.
10. Never allow children or inexperienced operators to operate or repair the mixer.
11. Use only factory authorized parts for replacement
12. Keep these operation instructions with the machine at all times
13. Always wear safety glasses and safety shoes when operating and moving equipment
14. Safety decals – replace missing damaged safety decals.

2

Summary of Contents for 450DD












Reviews: