Kuzma Air Line Instruction Manual Download | Manualshive

Page: 2 / 19

background image

2

KUZMA LTD

INSTRUCTION MANUAL FOR AIR LINE tonearm

The Air line tonearm is a very precisely engineered piece of equipment. However the
construction is robust and requires minimal maintenance for optimal performance.

CONTENTS:                                                 Page

1.0. General description                                     3
2.0. Unpacking                                                    4
3.0. Setup description                                         5
4.0. Air supply Setup                                        6-9
5.0. Tonearm Setup                                          10-14
5.1. Basic Setup                                                  10
5.3. Adjustment of tracking force                    10
5.4. Adjustment of tangential geometry         11-12
5.5. Fine horizontal levelling                             13
5.6. Adjustment of VTA                                    13
5.7. Adjustment of azimuth                               14
5.8. Adjustment of cueing device                      14
6.0. Operation of the tonearm                           14
7.0. Damping                                                       15
8.0. Zero switch kit                                             16
9.0. Maintenance                                                16
10.0. Troubleshooting                                     18-19

Small ring

«
1
2
3
4
...
»

Summary of Contents for Air Line




















Reviews:

No comments

Related manuals for Air Line

Brand: Technics Pages: 15

ProTab 26XXL IPS

Brand: Point of View Pages: 12

Brand: Jiaxing Lynx Displays Co., Ltd Pages: 10

Brand: Iget Pages: 54

Brand: Jam Pages: 2

Brand: MPMan Pages: 25

Brand: Lava Pages: 50

Brand: Samsung Pages: 2

Brand: Samsung Pages: 22

Brand: Samsung Pages: 20

Brand: Samsung Pages: 37

Brand: Samsung Pages: 59

Brand: Samsung Pages: 66

Brand: Samsung Pages: 78

Brand: Samsung Pages: 98

Brand: Samsung Pages: 119

Brand: Samsung Pages: 134

Brand: Samsung Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands