background image

Description

The ESR215 is a dedicated Full Range System.

Incorporating Patent Pending-Proprietory 

components, specifically matched to bespoke 

electronics. Exceptionally flat frequency 

response and Very High Definition sound 

system. Emphasizes every detail and nuance of a 

performance and transfers the atmosphere to each 

and every audience member

Applications

  Intentionally designed for use in Theatres 

and Cultural Centers to provide the 

highest audio quality from single Column 

enclosures for stage sides and prosceniums 

for medium to larger venues

  Fixed Installations

  Music venues

  Classical and opera concerts

Features

  High-output, full-range 3-way loudspeaker 

system

  132dB sustained output

  Wide dispersion at high frequencies, controlled 

at lowmids to reduce indoor reflections

  Mid/High horn design provides optimized 

transducer loading and controlled dispersion

  Patent-Pending 3” diaphragm nitride-titanium 

compression driver with complex geometry 

phase plug and and neodymium magnetic 

motor structure for higher output and lower 

distortion performance

  Eight-inch midrange driver with 3” (76mm) 

neodymium magnetic motor structure for 

increased control and output and decreased 

distortion and weight

  Proprietary midrange heat dissipation system 

controls voice coil temperature, ensures high 

dynamics and extends transducer lifespans

  Front-loaded, 15-inch mid-bass driver with 

3.00” (76mm) voice coil assembly and ferrite 

magnetic motor structure

  Professional, exterior-grade Baltic birch 

construction with wear-resistant polymer 

coating Proprietary corner and side handle 

designs for simplified handling and carrying

  Acetal copolymer high impact, low friction 

feet allowing other cabinets lock-in and easy 

cabinet movement

  Six internal corner and one back brace with 

M10 suspension points and side and top and 

bottom handles with M10 suspension points.  

A total of 17 suspension points are available for 

custom installation applications

  Requires ESR3000 unit for control electronics 

and amplification

ESR Full Range Sound System  Benefits

 

Total flexibility

 

ESR Series does not require a large number of 

speakers. Provides a full range, very high quality 

sound from single, small, location. For extended 

bass  use from a wide range of subwoofers. 

Subwoofers can be placed in a large place range, 

because of the 70Hz crossover point between ESR 

module and subwoofer. 

 

Superb sound

Greater dynamic range than any current active 

design. Features Very High Definition technology 

with Super Analog amplifier. 

Easy set-up

Plug-and-play connection to ESR3000 amp/

processor module. Cabinet features top handles, 

seven suspension points and “integral feet” for easy 

positioning on stage.

Dr

awing

ESR3000

ESR215

O

ver

view

Overview

12

11

ESR215  

The Ultimate, Full Range, Large Scale System  

part num.

  KVV 987 245

FULL RANGE MODULE

Summary of Contents for ESR215
























Reviews: