background image

Kvaser Memorator 2xHS v2 User’s Guide

14 (26)

4

Appendices

In this section you will find technical information about the Kvaser Memorator 2xHS
v2 and its connectors.

4.1

Definitions of LED states and colors

A Kvaser device has two basic types of LEDs; Power and Traffic. These are dual
colored as shown in Table 2. A device with multiple CAN channels has one Traffic
LED for each CAN channel. When the device has more than one channel a space
and digit is added on the label, CAN 1, CAN 2 etc. The red Traffic LEDs are also
used to indicate errors by using all red Traffic LEDs simultaneously.

LED

Label

Color

Power

PWR

Green/Yellow

Traffic

CAN

Yellow/Red

Table 2: The different type of LEDs.

The following definitions is used to describe the state of an LED:

Off

The LED is off and no light is emitted.

Flash

The LED is lit up for a very short time. A single flash may be hard to see

and a continuous set of flashes will look the same as On.

Slow Blink

The LED is repeatedly turned On and Off. The On and Off phase is

equal in time.

Fast Blink

The LED is repeatedly turned On and Off but with a higher frequency

than Slow Blink. The On and Off time is still equal.

On

The LED is constantly emitting light.

Slow Waver

This is a variant of Slow Blink but instead of being Off, a second color

is On. This is only possible with a dual colored LED.

Fast Waver

The LED is alternating between two colors as in Slow Waver but

using a higher frequency.

Running

This means that all LEDs are lit, one at the time, in sequence with every

color available i.e. “Power green->Power yellow->Traffic 1 yellow->Traffic 1
red->Traffic 2 yellow->Traffic 2 red->. . . ”

As an example, "Slow Waver (Green/Yellow)" means that the LED is slowly blinking
by alternating between green and yellow.

Kvaser AB, Mölndal, Sweden — www.kvaser.com

Summary of Contents for Memorator 2xHS v2



























Reviews: