background image

Kvaser PCIcan Hardware Reference Manual 

 

19(21) 

                            

Kvaser AB, Mölndal, Sweden — www.kvaser.com 

 

 

8  Legal Information 

 

 

8.1  RoHS Directive 

This line of products will never comply with the RoHS (Restriction of Hazardous Substances) 
directive when it becomes effective 1 of July 2006. However, the complete line of Kvaser 
PCIcanx boards will achieve full conformance to the RoHS directive when it becomes 
effective 1 of July 2006. Kvaser PCIcan and Kvaser PCIcanx is fully software compatible with 
each other. 

 

8.2  Copyright 

This document is Copyright © 2001-2008 Kvaser AB. This document may not be reproduced 
without our written permission. Infringement will render the user liable to prosecution.  
 
We believe that the information contained herein was accurate in all respects at the time of 
printing. Kvaser AB cannot, however, assume any responsibility for errors or omissions in this 
text. Please also note that the information in this document is subject to change without notice 
and should not be construed as a commitment on the part of Kvaser AB. 

 

8.3  CE Marking Directive 

This line of products has been CE marked. We will be pleased to inform you on which 
standards this equipment has been tested for compliance. 
 

NOTE: 

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a  Class  A 

digital  device,  pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide 
reasonable  protection  against  harmful  interference  when  the  equipment  is  operated  in  a 
commercial  environment.  This  equipment  generates,  uses,  and  can  radiate  radio  frequency 
energy  and,  if  not  installed  and  used  in  accordance  with  the  instruction  manual,  may  cause 
harmful  interference  to  radio  communications.  Operation  of  this  equipment  in  a  residential 
area is likely to cause harmful interference in which case the user will be required to correct 
the interference at his own expense.

 

 

8.4  Trademarks and patents 

All product names mentioned in this manual are registered or unregistered trademarks of their 
respective owner. Windows® is a registered trademark of Microsoft Corporation in the United 
States and other countries. Linux® is the registered trademark of Linus Torvalds in the United 
States  and  other  countries.  The  products  described  in  this  document  are  protected  by  U.S. 
patent 5,696,911. 
 

Summary of Contents for PCIcan






















Reviews: