KWB TT 14, Instructions For Use Manual

TECHNICAL DATA

• Magazine capacity: 110 mm

• Uses kwb staples, lengths from 6 to 14 mm (see technical label stuck on the tool) and kwb brads for 

  electric tools.

• Maximum drive speed: 3 pcs. per second.

• Maximum average fastener drive rate: 20 fasteners per minute.

• Nominal voltage: 220/240 V ~ - 50/60 Hz

• 10 A electric supply outlet

• Cable extention lengths 10 m (2x1,5 mm2) max 15 m (2x2,5 mm²) heavy duty

• Trigger lock to prevent accidental fastener drive

• Double insulated CLASS II

• Dimensions: 180x150x50 mm

• Weight: 0,830 Kg approx

• Noise level at 20 shots/min. LpA = 83 dB

• Vibrations at 20 shots/min. <2,9 m/s²)

LOADING OF STAPLES

 - See Figures 1-2-3-4

Before operating, make sure you chose correct type of staples. For better result, always use genuine staples.

• Unplug the tool

• Hold and keep the tool steady as shwon.

• Press the rear button of the magazine (3) to unhook it from the tacker body (4)

• Slide the magazine slider backwords (5)

• Insert staple strip (6)

• Close the magazine slider (5) by pushing the rear button forward (3) by hand and hook it to the tacker body (4)

BRAD LOADING

 - Figure 5 Same loading operations as shown for the staples. But be careful to insert the brad strip (14) 

into its proper seat as shown in figure (15).

OPERATING INSTRUCTIONS

 Fig. 6-7-8

• hold the tool (4) firmly against the surface (7) to be stapled.

• Unlock safety (8) by bringing it from vertical position (8/1) into horizontal position (8/2)

• Pull the trigger (9) for each staple to drive.

WARNING: DANGER

• Do not operate the tool empty, in the air or into materials for which it is not intended.

• Always disconnect the stapler from the powersupply after use.

MAINTENANCE

Fig. 10

• Unplug the tool and unload the magazine.

• Clean the slide areas with a jet of compressed air.

• Clean the outside with a damp cloth.

• Never use solvents or other liquids in the cleaning operations.

• Occasionally lubricate the outlet staple area with a drop of mineral oil (13)

• Do not lubricate the internal parts of the staplers

• Do not disassemble or alter the stapler.

• All repairs must be performed by specialized personnel only.

• When requesting technical or commercial assistance, always quote type/model of tool, serial number, voltage and 

  fasteners used.

NEVER REMOVE THE TECHNICAL LABEL (fig. 11)!

In conformity with the standard CEI EN 50144-1/A1 “Safety of the electric tools”

In case of damage to the cable, to avoid any possible risk of injury, the cable must be replaced only by the manufacturer, or through his Service Department or 

anyway by a qualified personnel.

IMPORTANT NOTICE TO THE USERS

 – In conformity with Art. 13 of Law Decree dated July 25th, 2005, n. 151 “Fulfilment of the Directives 2002/95/CE, 

2002/96 CE and 2003/108/CE, on the restriction on use of certain hazardous substances in electrical and electronic equipments, and on waste electrical 

and electronic equipment” (WEEE)

The symbol of the crossed-out wheeled bin marked on the electric equipment means that the product at the end of its life cycle must be collected sepa-

rately from other types of waste. Therefore the user will have to deliver the equipment that reached the end of its life cycle to proper separate collection facilities 

of electronic and electric waste. Or he must deliver it to the dealer when purchasing a new similar electrical equipment, on one-to-one basis. The proper separate 

collection to convey the disued equipment for recycling, treatment and waste in compliance with the environmental directions will help to avoid possible negative 

environmental effects and on the human health and will help recycling of the materials of the electrical equipment. Direct and abusive waste of the product from 

the user will allow application of the penalties as per D.Lgs. n. 22/1997 (Article 50 and following ones of D.Lgs. n. 22/1997).

DECLARATION OF CONFORMITY

kwb Germany GmbH, 28816 Stuhr declare under our sole responsibility 

that the product TT 14 to which this declaration relates is in conformity with 

the following standards or other normative documents EN50144-1:1995, 

prEN50144-2-16:1996, EN55014:1991, EN55014-2:1997, EN61000-3-2:1995, 

EN61000-3-3:1995 the following provisions of Directive MD98/37/EEC, 

LVD73/23/EEC, EMC89/336/EEC

GB

5

Produktentwicklung

kwb Germany GmbH · Hauptstrasse 132

28816 Stuhr, Germany · www.kwb.eu

TT 14 BedAnleitung 24sprachig.indd   5

27.01.15   13:08