Alert
Reason
Solution
Keypad flashes red once with
one beep*.
One incorrect code entered.
Re-enter code.
Keypad flashes red three
times with three beeps*.
No user code programmed.
Program at least one user code.
Programming timeout after five
seconds.
Attempt programming procedure again.
Unsuccessful programming.
Keypad flashes red 15 times
with 15 beeps*
Three incorrect codes entered
within one minute.
Re-enter code after 60 second keypad
lockout.
Keypad flashes red with fast
beeping sound for three to
four seconds.
Low battery.
Replace batteries.
Keypad flashes green with
continuous beeping sound
for two seconds.
Door jammed while attempting
to lock.
Manually re-lock door. If needed,
reposition strike.
Lock beeps continuously.
Interior assembly is
disconnected from exterior.
Remove battery pack, reconnect the interior
to the exterior, then reinstall battery pack.
*Beeping sound will only be heard if switch #3 is on.
© 2016 Spectrum Brands, Inc.
1.
Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user codes and mastercode.
5. Dispose of used batteries according to local laws and regulations.
CAUTION:
Prevent unauthorized entry. Since anyone with access to the back panel
can change the user codes, you must restrict access to the back panel and routinely
check the user codes to ensure they have not been altered without your knowledge.
The use of a mastercode can help protect your system’s settings.
WARNING:
This Manufacturer advises that no lock can provide complete security
by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder’s hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualified locksmith or other security professional.
Important Safeguards
If no button is pressed for five seconds, the system will time out, and
you will need to restart the procedure.
1 Keep door open.
Press Program
button once.
5 Re-enter user code.
6 Press Lock
button once.
If unsuccessful
Make sure to enter
the same valid code
in steps 3 and 5.
Test code
While the door is
open, test the user
code to make sure
it no longer unlocks
the door.
2 Press Lock
button once.
4 Press Lock
button once.
3 Enter user code
to be deleted.
Network Information
Z-Wave System Notes
This product is a security enabled Z-wave Plus product and must be used with a Security
Enabled Z-Wave controller to be fully utilized. Z-Wave is a “Wireless mesh network,” and
results may vary based on building construction and communication path.
To assure interoperability, each Z-Wave product must pass a stringent conformance test to
assure that it meets the Z-Wave standard for complete compliance with all other devices and
controls. The Z-Wave identity mark assures consumers, integrators, dealers and manufacturers
that their products will reliably perform with any other Z-Wave device. And, regardless of the
vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.
Z-Wave Configuration and Association Parameters are available
on the SmartCode 914 page at www.kwikset.com.
Removing the lock from the network
Follow your smart home system’s instructions
to remove the lock from the network. When
prompted by the system, press button A” on the
lock interior once.
4 / 4
SmartCode at a Glance
Deleting a single user code
Note: All codes may be deleted at once if the mastercode is enabled. For more information about the
mastercode, consult the Programming and Troubleshooting Guide.
Reference Guide
Exterior
Back
panel
Program
button
Status
LED
Switches
Turnpiece
shaft
Note: When the cover is removed,
the turnpiece shaft can be used to
manually lock and unlock the door.
Interior (cover removed)
Switches and Status LED colors
Troubleshooting
Switch
Function
1
Door lock status LED blinks every 6
seconds
2
Lock automatically re-locks door 30
seconds after unlocking. Disabled if no
codes are programmed.
3
Audio
4
Not used.
Color
Lock Status
Blinking green
Unlocked
Blinking amber
Locked
Blinking red
Low battery
Solid red
Door handing process
did not work properly.
See the online
Programing and
Troubleshooting Guide.
1 2 3 4
On
Switches
Status
LED
Off
System Alerts
Factory Reset
A factory reset will delete all codes associated with the lock,
and it will remove it from your smart home system.
Status
LED
1 Remove
battery pack.
2 Press and HOLD the Program
button while reinserting
the battery pack.
Keep holding the button for 30
seconds until the lock beeps
and the status LED flashes red.
Keypad
Lock
button
Keyway
SmartKey
tool hole
Button “A”
Button “B”
3 Press the Program button
once more. When the LED
flashes green and you
hear one beep, the lock
has been reset.
4 Perform the door handing process again
to teach the lock the orientation of the
door, pair the lock with your smart home
system, and add user codes to your lock.
A complete Programming and Troubleshooting Guide is
available on the SmartCode 914 page at www.kwikset.com.
