KYMCO MXU 500 Owner'S Manual Download

Page: 14 / 664

SAFETY INFORMATION

AN ATV IS NOT A TOY AND CAN BE HAZARDOUS TO OPERATE.

An ATV handles differently from

other vehicles including motorcycles and cars. A collision can occur quickly, even during routine

maneuvers, if you fail to take proper pre-cautions.

SEVERE INJURY OR DEATH can result if you do not follow these instructions:

Never operate an ATV without wearing an approved motorcycle helmet that fits properly. You

should also wear eye protection (goggles or face shield), gloves, boots, long-sleeved shirt or

jacket, and long pants.

- A child under 16 years old should never operate an ATV with engine size greater than 90cc.

Read this manual and all labels carefully and follow the operating procedures described.

Never operate an ATV without proper training or instruction.

Beginners should receive training from a certified instructor.

Always follow the age recommendation:

Never allow a child under age 16 to operate an ATV without adult supervision, and never allow

continued use of an ATV by a child if he or she does not have the abilities to operate it safely.

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MXU 500

Reviews:

Related manuals for MXU 500

Brands by name

Popular brands

KYMCO MXU 500, Owner'S Manual

Search results

Summary of Contents for MXU 500

Reviews:

Related manuals for MXU 500

Brands by name

Popular brands