KYMCO MXU 500 Owner'S Manual Download

Page: 466 / 664

. DRIVE TRAIN

13-33

MXU 500

If the backlash it too small, replace the right

side shim(s) with a thicker one.
If the backlash too large, replace the right

side shim(s) with a thinner one.
If the right side shim was changed with a

0.1 mm thicker shim, replace the left side

shim with one that is 0.1 mm thinner.

LEFT SIDE SHIM SELECTION

Install the removed right side shim(s) and

front drive assembly.
Put a few pieces of solder (O.D.: 1.2 –2.5

mm/L: 6 mm) on the bearing outer race, as

shown.

Assemble the gear case and tighten its bolts

to the specified torque in a crisscross pattern

in 2 or 3 steps.

Torque:

2.3 kgf-m (23 N-m, 16.5 lbf-ft)

Do not install the left side shim(s) at

this time.

Apply a small quantity of grease to the

solder to prevent them from falling

＊

Do not apply a sealant to the mating

surface of the gear case.

Do not apply a sealant to the case

bolts.

＊

It is important to turn the pinion while

tightening the bolts. If the ring gear

shim is too thick, the gears will lock

after only light tightening.

＊

Summary of Contents for MXU 500

























































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for MXU 500

Reviews:

Related manuals for MXU 500

Brands by name

Popular brands

KYMCO MXU 500, Owner'S Manual

Search results

Summary of Contents for MXU 500

Reviews:

Related manuals for MXU 500

Brands by name

Popular brands