2NC/2NF/2NG/2NN/3P7/3P8/3P9
1-4-68
(1) No image appears (entirely white).
Print example
Cause of trouble
1. No or defective developing bias output.
2. Failure of the rotation of the developing roller.
3. Defective transfer.
4. Laser is not dispersed from the laser scanner unit (LSU).
5. The drum does not rotate.
Defective part
Check description
Corrective Action
1
Developing unit
Executing U089 to generate PGs
and check the following :
Check whether the developer
drive gear is damaged.
If the gear is damaged, replace the developer
unit.
Check the developing roller is
rotated by hand.
If the developer unit is in fault, replace the
developer unit. (see page 1-5-35)
Check contamination and defor-
mation on the terminals of devel-
oper unit or the high-voltage
PWB1.
If the connecting terminals are dirty, clean.
If the connecting terminals are deformed,
correct for a proper conduction.
2
High voltage PWB
Check the connection of the con-
nector(s) and the high voltage
PWB. Or, verify conduction of
the wires.
Reinsert the connector if it its connection is
loose.
Replace the cable if it has no conduction.
High voltage PWB (YC 1) and main/engine
PWB (YC3)
Check if developing bias value at
its default by U140.
1. If the value obtaines by U140 does not
conform to the default value, reset it to the
default. (see page 1-3-51)
2. Replace the high-voltage PWB.
3
Transfer unit
Check if the right cover is closed. If the right cover has not been closed,
check how the conveying guide is locked and
open the conveying guide once, then close.
4
Laser scanner unit
(LSU)
Check the connection of the con-
nectors.
Or, verify conduction of the
wires.
1. Reinsert the FFC wire if it its connection is
loose.
Replace the cable if it has no conduction.
2. Replace the LSU
(see page 1-5-27)
5
Main/Engine PWB
A control signal is not derived
from the main/engine PWB.
Replace the main/enging PWB.
(see page 2-2-11)
Summary of Contents for DP-480
