2JZ/2JX/2JV/2H7-5
1-3-129
U464
Setting: [Permission]
1. Select ON or OFF.
Initial setting: ON
2. Press the start key. The setting is set.
Setting: [Set Time Interval]
1. Change the setting value using the +/- or numeric keys.
2. Press the start key. The value is set.
Setting: [Set Sleep Period for Calib]
1. Change the setting value using the +/- or numeric keys.
2. Press the start key. The value is set.
Setting: [Permission Act.(50sheets)]
1. Select ON or OFF.
Initial setting: ON
2. Press the start key. The setting is set.
Setting: [Permission (ON/Sleep out)]
1. Select ON or OFF.
Initial setting: ON
2. Press the start key. The setting is set.
Setting: [Permission (AP/NE)]
1. Select ON or OFF.
Initial setting: ON
2. Press the start key. The setting is set.
Maintenance
item No.
Description
Display
Description
ON
Turns calibration ON
OFF
Turns calibration OFF
Display
Description
Setting range
Initial setting
COUNT
Setting the interval time of calibration
0 to 9999 (s)
480
Display
Description
Setting range
Initial setting
Time(min)
Setting the standard time of sleep mode
0 to 480 (min)
60
Display
Description
ON
Enables permission to execute at continuously 50 pages
OFF
Disables permission to execute at continuously 50 pages
Display
Description
ON
Executes calibration if fuser temperature is less than 50
C/122
F at
power-up or recovery from auto sleep mode
OFF
Executes calibration regardless of fuser temperature at power-up or
recovery from auto sleep mode
Display
Description
ON
Paper interval calibration at the time of calibration/near end after
toner feed is carried out
OFF
Paper interval calibration at the time of calibration/near end after
toner feed is not carried out
Summary of Contents for TASKalfa 250ci
