Kyocera TASKalfa 250ci Service Manual Download | Manualshive

Page: 247 / 626

background image

2JZ/2JX/2JV/2H7

1-4-29

C0880

Program archive problem (optional
fax)

When power is turned on, the com-
pressed program in the Flash ROM on
the fax control PWB was not success-
fully decompressed.

Defective fax soft-
ware.

Install the fax software.

Defective fax con-
trol PWB.

Replace the fax control PWB and verify the
operation.

C0890

Fax control PWB CG FONT archive
problem (optional fax)

When power is turned on, the com-
pressed CG font in the Flash ROM on
the fax control PWB was not success-
fully decompressed.

Defective fax soft-
ware.

Install the fax software.

Defective fax con-
trol PWB.

Replace the fax control PWB and verify the
operation.

C0920

Fax file system error

The backup data is not retained for file
system abnormality of flash memory of
the fax control PWB.

Defective fax con-
trol PWB.

Replace the fax control PWB and verify the
operation.

C1010

Lift motor 1 error

After cassette 1 is inserted, lift switch 1
does not turn on within 12 s. This error is
detected four times successively.

Poor contact in the
connector termi-
nals.

Check the connection of connector of lift
motor 1 and the connector YC3 on the feed
PWB, and the continuity across the connec-
tor terminals. Repair or replace if necessary.

Broken gears or
couplings of lift
motor 1.

Replace lift motor 1.

Defective lift motor
1.

Check for continuity across the coil. If none,
replace lift motor 1.

Defective lift switch
1.

Check if YC4-2 on the feed PWB goes low
when lift switch 1 is turned off. If not, replace
lift switch 1.

Poor contact in the
connector termi-
nals.

Check the connection of connector of lift
switch 1 and the connector YC4 on the feed
PWB, and the continuity across the connec-
tor terminals. Repair or replace if necessary.

Defective PWB.

Replace the feed PWB or engine PWB and
check for correct operation.

C1020

Lift motor 2 error

After cassette 2 is inserted, lift switch 2
does not turn on within 12 s. This error is
detected four times successively.

Poor contact in the
connector termi-
nals.

Check the connection of connector of lift
motor 2 and the connector YC3 on the feed
PWB, and the continuity across the connec-
tor terminals. Repair or replace if necessary.

Broken gears or
couplings of lift
motor 2.

Replace lift motor 2.

Defective lift motor
2.

Check for continuity across the coil. If none,
replace lift motor 2.

Defective lift switch
2.

Check if YC4-8 on the feed PWB goes low
when lift switch 2 is turned off. If not, replace
lift switch 2.

Poor contact in the
connector termi-
nals.

Check the connection of connector of lift
switch 2 and the connector YC4 on the feed
PWB, and the continuity across the connec-
tor terminals. Repair or replace if necessary.

Defective PWB.

Replace the feed PWB or engine PWB and
check for correct operation.

Code

Contents

Remarks

Causes

Check procedures/corrective measures

«
...
245
246
247
248
249
...
»

Summary of Contents for TASKalfa 250ci



















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKalfa 250ci

Pixma G1000 series

Brand: Canon Pages: 2

Pixma G1000 series

Brand: Canon Pages: 80

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 44

Brand: Oki Pages: 24

Brand: VAF instruments Pages: 24

Brand: Magicard Pages: 26

Brand: QMS Pages: 194

WorkCentre 7800 series

Brand: Xerox Pages: 14

WORKCENTRE 7775

Brand: Xerox Pages: 15

WORKCENTRE 7775

Brand: Xerox Pages: 24

WORKCENTRE 7755

Brand: Xerox Pages: 252

WORKCENTRE 7755

Brand: Xerox Pages: 15

WORKCENTRE 7755

Brand: Xerox Pages: 40

WorkCentre 5019

Brand: Xerox Pages: 50

versalink C7020

Brand: Xerox Pages: 20

WorkCentre 4265

Brand: Xerox Pages: 4

Brand: Xerox Pages: 4

Brand: Xerox Pages: 281

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands