manualshive.com logo in svg

Kyocera TASKalfa 250ci, Service Manual

The Kyocera TASKalfa 250ci is a high-performance multifunctional printer equipped with advanced features. This versatile device comes with an easy-to-understand Operation Manual, available for free download from our website. Get the most out of your printer by referring to the comprehensive manual for efficient and hassle-free operation.

Share
Download
background image

2JZ/2JX/2JV/2H7-1

1-5-29

If manual color registration has failed:

9. If the balance between V-1 and V-5 is more than 2 scales (sample 1) or less than -2 

scales (sample 2), perform the following steps:

Figure 1-5-49

10. Open the front cover. Push the release button and pull out the waste toner tray.
11. Release two hooks and then remove the waste toner tray.
12. Rotate the adjustment knob using a 5 mm hex wrench.

Direction of rotation
(V-1 - V-5) >= 2 scales (sample 1): rotate counterclockwise.
(V-1 - V-5) <= -2 scales (sample 2): rotate clockwise.
Number of rotation
(V-1- V-5) x 4 clicks

13. Refit the toner container and close the front cover.
14. Turn the main power switch off and on. Correction automatically starts.
15. Print a reference chart and verify the result.

Figure 1-5-50

V-1

Sample 1

V-2

V-3

V-4

V-5

V-1

Sample 2

V-2

V-3

V-4

V-5

Hook

Hook

Hex wrench

Waste toner tray

Release button

Adjustment knob

Adjustment knob

Adjustment knob

Adjustment knob

Summary of Contents for TASKalfa 250ci



















































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKalfa 250ci

Fuji Xerox ApeoSport C5540I Quick Reference Manual preview
ApeoSport C5540I
Brand: Fuji Xerox Pages: 108
Xerox 5550B - Phaser B/W Laser Printer Administrator'S Manual preview
5550B - Phaser B/W Laser Printer
Brand: Xerox Pages: 117
Xerox WorkCentre 3345 Quick Use Manual preview
WorkCentre 3345
Brand: Xerox Pages: 18
Olivetti FS-529 Service Manual preview
FS-529
Brand: Olivetti Pages: 33
Cashino CSN-80V User Manual preview
CSN-80V
Brand: Cashino Pages: 74
ABLE Ap1400 Programmer'S Manual preview
Ap1400
Brand: ABLE Pages: 42
Lexmark Monochrome Laser Installation Sheet preview
Monochrome Laser
Brand: Lexmark Pages: 1
Protech Systems MP-1060 User Manual preview
MP-1060
Brand: Protech Systems Pages: 140
Xerox WorkCentre 7970 System Administrator Manual preview
WorkCentre 7970
Brand: Xerox Pages: 268
Konica Minolta bizhub PRO C65hc Additional Information preview
bizhub PRO C65hc
Brand: Konica Minolta Pages: 24
Go ET-15000 SP Setup preview
ET-15000 SP
Brand: Go Pages: 3
QMS qms-ps 800+ User Manual preview
qms-ps 800+
Brand: QMS Pages: 188
Sinfonia Technology DP-1045 Operation Manual preview
DP-1045
Brand: Sinfonia Technology Pages: 41
IBM 3852-2 Hardware Reference Manual preview
3852-2
Brand: IBM Pages: 128
Canon IMAGERUNNER 2020 Copying Manual preview
IMAGERUNNER 2020
Brand: Canon Pages: 115
Canon ImageRUNNER ADV Black & White Copy Manual preview
ImageRUNNER ADV
Brand: Canon Pages: 42
Canon imageRUNNER ADV Colour Copy Manual preview
imageRUNNER ADV Colour
Brand: Canon Pages: 54
Canon imageRUNNER ADVANCE 8500 III Series Customer Expectation Document preview
imageRUNNER ADVANCE 8500 III Series
Brand: Canon Pages: 108

Brands by name

Popular brands

Load more brands